眉毛线条也可以是直的,不用过于弯曲使脸显得不那么圆。
It should also be straight and not too curvyto downplay the roundness of the face.
从弹塑性理论出发以圆截面轴为例对校正应力与残余变形进行了分析研究,提出了在给定弯曲误差下的校正载荷的计算公式。
The paper has studied straightening stress and residual deformation of circular shaft by using elastic - plastic theory, deueloped calculation formula of straightening loud in given deflection error.
当缝合这两种类型的裁片时,就放在上面一层的裁片而言,是不难的且很快就能掌握,但发现缝至弯曲的凸出部位最凸出的部分时,不太容易使其缝合圆顺。
There is no hard and fast rule as to which piece is placed on the top when working with these shapes, but it hat been found that distortion is less likely to occur when the outer curve is uppermost.
分析了滚刀齿高和齿顶倒圆半径对所切齿轮齿根弯曲应力的影响。
And it analyzed that hob tooth height and tooth top pour round radius impacted on gear tooth root crooked stress.
本文对极正交各向异性圆板在任意轴对称载荷和边界条件下的非线性弯曲问题进行了较为系统的研究。
This paper presents a systematical investigation of the nonlinear bending of polar orthotropic circular plates under arbitrarily axisymmetric loads and a variety of boundary conditions.
同时还利用计算机图形学原理,对管件外圆表面直线段、弯曲段的三维绘制进行处理分析。
Meanwhile, the drawing regulations about line segments and curly segments of tube bending surface are analysed.
本文给出了粘弹性基支粘弹性圆(环)形薄板准静态弯曲的一般解法。
In this paper, a general solution for quasistatic bending of viscoelastic circular (ring) thin plate rested, on viscoelastic foundation is given.
本文研究了厚度按线性规律变化的圆薄板在中心集中力作用下的非线性弯曲问题。
Nonlinearly bending problems, of circular thin plates with linearly varying thickness under central concentrated load are discussed.
以幂函数为试函数,用配点法计算了夹层圆板和夹层扁球壳的非线性弯曲。
Taken power function as a trial function, nonlinear bending of circular sandwich plates and shallow spherical sandwich shells was discussed by means of point collocation.
如图所示的管卡,它使用圆的、方的或长方形钢板,使其弯曲与管子外园贴合。
Pipe clamps similar to this illustrated in the figure were developed that utilized round, square, or rectangular pieces of steel curved to fit the outside of the pipe.
它有两个与贯穿轴圆终板在他们中间悬挂和纵向弯曲叶片之间。
It has two circular endplates with the shaft running through the middle of them and curved vanes strung longitudinally between them.
本文应用文提出的方法,研究受内点对称支承,在均布载荷作用下的弹性圆板的弯曲。
Using the method proposed by this paper, deals with bending of the uniformly loaded elastic circular plates with internal symmetrical point supports.
对周边为弹性支承边界条件下的功能梯度材料圆板轴对称弯曲问题进行了分析。
The paper presents an analysis of the axisymmetric bending of a functionally graded circular plate under elastically supported boundary condition.
当你在它,它会是一个好主意,让你的车轮平衡来确定你的钢圈的确是圆的,不弯曲。
Whilst you're at it, it would be a good idea to get your wheels balanced to determine if your rims are indeed round and not bent.
介绍一种卷圆工艺和模具,并对模具弯曲成形过程进行了分析,指出该方法可以用于级进模上成形。
It has been recommended a technology and die of bending ring with analysis of its forming process, using in that of bending ring in progressive forming die.
同时对圆棒料的弯曲回弹进行了理论分析。
At the same time, the spring back allowance of bottoming bending of circle section rod is analyzed.
本文探讨了纤维增强复合材料正交对称铺设层合圆板的大挠度弯曲问题。
The large deflection problems of the symmetrically laminated cross-ply circular plates of fiber reinforced composites are investigated in this paper by using Galerkins procedure.
提出了弹性地基上圆板承受轴对称载荷作用弯曲问题的一种新的解法-迭代法。
In this paper, a new method, the successive substitution method, is presented for bending of circular thin plate loaded by axial symmetrical force on elastic foundation.
提出了弹性地基上圆板承受轴对称载荷作用弯曲问题的一种新的解法-迭代法。
In this paper, a new method, the successive substitution method, is presented for bending of circular thin plate loaded by axial symmetrical force on elastic foundation.
应用推荐