当齿沟啮合面旋转至壳体排气口时，较高压力的油气混合气体排出机体。
When the mesh surface rotation teeth to shell vent, under high pressure gas mixture in the oil and gas discharge.
这些公式适用于齿面啮合的任何接触点。
These formulae are suitable for any contacting point of tooth surface meshing.
应用赫兹理论和齿轮啮合理论给出了螺旋齿轮齿面接触应力的计算方法和相关公式。
A calculation method and corresponding formulas are presented by using Hertz contact theory and gear mesh theory.
本文在极低速情况下，模拟测定了仪表齿轮在一齿啮合过程中两齿轮齿面间摩擦系数的变化情况。
The friction factor between two tooth surfaces of instrument gears during one meshing process is imitatively measured in this paper under the condition of ultra-low-speed.
一般齿轮齿形曲线在一点邻域的高阶阶戴劳级数展开后，会发现齿面啮合点邻域间隙为2阶无穷小。
The common gear tooth profile curve launches after neighborhood higher order step taylor's series, can discover the tooth face meshing point neighborhood gap is 2 step infinitely greats.
提出了运动优化的方法，通过预设传动误差抛物线函数，使齿面啮合时运动误差和不连续性减至最小。
The motion optimization method is proposed, by which transmission errors anddiscontinuousness of tooth surface meshing is decreased to minimum.
根据空间啮合原理以及坐标关系推导被加工左右旋齿轮的齿面方程；
Tooth face equation of producing gear is derived based on spatial meshing theory and coordinate relation.
通过分析锥齿轮的加工方法和齿轮啮合理论，建立了螺旋锥齿轮齿面数学模型。
A mathematical model of spiral bevel gear tooth surface was built by analyzing manufacture method and meshing theory.
以圆矢量函数为工具，推出了误差条件下的渐开螺旋面方程，并以啮合线为媒介，建立了测量蜗杆误差补偿的数学模型。
With the tool of circle vector function, the involute helix profile with error is given, and with the media of engagement line, the error compensation mathematical model is established.
结合机床调整参数、齿轮啮合原理，建立了螺旋锥齿轮齿面误差修正模型。
The error correction model of tooth surface was established by machine tool adjustment parameters and meshing principle.
在少齿差内啮合传动中，存在多对接近啮合的小间隙齿面于理论啮合点左右，轮齿受力产生的微小变形使得某些对齿面相互接触进入啮合状态。
In small tooth difference of inner meshed transmission, there were a few pairs of tooth faces which were apart from each other for a small gap beside the contact point generated by two meshed teeth.
结果表明，齿面弹性变形引起的齿轮轮齿的微小转动对啮合点的最终位置有一定的影响。
The results show that the micro rotational Angle induced by the tooth surface elastic deformation has definite effect on meshing points.
面齿轮啮合分析包括了两部分。
目前，复杂周转轮系的功率流分析、传动比和啮合效率的计算既困难又繁复，而应用离散分析法可以改变这一局面。
It is difficult and complicated to analyze the power-flow of the complex epicyclic gear trains and compute their transmission ratio and meshing efficiency.
获得了在啮合过程中不同的啮合位置面齿轮的接触应力的分布规律。
The distribution of the contact stress of FG is obtained in the different meshing locations during the meshing.
研究结果表明：接触应力、上扣扭矩、螺纹啮合时的几何约束，是齿面粘扣的力学要点。
The research result states that the contacting stress, thread torque and thread joggle geometry restriction are mechanical points of the sticky thread.
内啮合弧面凸轮机构可用作高效大转矩的减速装置，有很好的应用前景与推广价值。
The inner engagement globoidal cams mechanism can be used for the high efficency and high torque speed reducer , and shows bright future in application.
齿面修形是提高齿轮副啮合性能的重要手段。
The modification of gear is a principal method for improving performance of meshing.
给出了超环面行星蜗杆传动啮合效率、齿面磨损量和弹流油膜厚度的分布规律及其随传动参数的变化规律。
The distribution of engaging efficiency, EHD oil film thickness and tooth face wear and their changes along with transmission parameters are presented.
以螺杆压缩机转子为例，介绍了未知螺旋面端截面轮廓及其啮合的共轭齿形求法，给出了实用计算公式。
Takes the screw type compressor rotor as an example, a calculating method of unknown section profile of spiral surface and its conjugate shape is introduced and practical formulas are given.
研究了活齿端面谐波齿轮各啮合副齿面修形的原则，得出了波发生器、活齿前后端和端面齿轮齿面的修形高度之间必须满足的关系。
The modification principle of tooth surface is deduced, and it draws the conclusion that the modificative tooth depth of wave producer, end face gear and oscillating teeth have certain relation.
外啮合珩齿工艺是一种效率高、成本低的硬齿面齿轮加工工艺，但对齿轮精度的提高有限。
Honing with a honing gear is an efficient and low - cost method for hard gear machining, but it can not obviously improve the precision of gear.
基于微分几何和空间啮合理论，分析了修正型圆环面双包络环面蜗杆副齿面形成原理。
Analysis of the forming principle of tooth flank of modified type worm gear pair was based on different geometry and spatial engaging theory.
在机构强度分析中，阐述了凸轮-针轮副啮合齿面接触强度、针齿销的弯曲强度计算和刚度计算。
Not only the contact strength between the CAM and the rollers is discussed, the flexural strength and rigidity of the rollers are also discussed.
渐开线内啮合弧面蜗杆是我们近几年来提出和研制的一种新型蜗杆传动。
This paper is the first report on theoretical research of the involute, internallyengaged, double-enveloping worm gear drive.
将齿轮因齿面变形而产生微小转角，继而进行齿面啮合分析的过程定义为拟赫兹接触分析。
The micro angle induced by the tooth surface elastic deformation causes the change of meshing points. Quasi-Hertzian analysis is defined as the process of tooth meshing analysis.
在建立了球齿轮齿廓曲面方程和啮合模型基础上，利用计算机仿真的方法对其进行了齿面接触分析研究。
After building the equations of tooth surfaces and the meshing model of a spherical gear pair, tooth contact analysis of spherical gear pairs is performed through simulation.
在建立了球齿轮齿廓曲面方程和啮合模型基础上，利用计算机仿真的方法对其进行了齿面接触分析研究。
After building the equations of tooth surfaces and the meshing model of a spherical gear pair, tooth contact analysis of spherical gear pairs is performed through simulation.
应用推荐