它是单螺杆压缩机工作过程热传导计算及啮合副加工的基础。
It is the basic to manufacture and heat transfer study in working process of this kind of compressor.
推导出了活齿端面谐波齿轮各啮合副经过齿面修形后的齿面方程。
The equations of teeth surface after modification of all key components, such as wave producer, oscillating teeth, end face gear, are deduced.
论文着重对新型锥形摆线行星传动啮合副的制造关键技术进行研究。
The paper focuses on the manufacturing key technologies of new conic cycloidal gear planetary transmission's mesh parts.
本文提出采用“圆台二次包络啮合副”作为单螺杆压缩机啮合副的型线。
This lubrication film is easily established with "straight line enveloping screw pair" rotors, but this kind of engagement pair is very difficult to machine.
本文研究摆线钢球减速器关键技术之一，无侧隙啮合副共轭齿形综合问题。
The paper researches one of the key techniques of the cycloid steel ball reducer, that is the synthesis of conjugate waves shapes for no gear clearance engagement pair.
单螺杆压缩机由一个圆柱螺杆和两个对称布置的平面星轮组成啮合副，装在机壳内。
Single screw compressor cylinder by a screw and two symmetrical layout of the plane composed of stars round of meshing pair, installed in the chassis.
针对摆线针轮啮合副接触应力较大，作者通过几种方案对比计算，提出了一组较好的摆线参数。
With the purpose to reduce the high contact stress of the meshing pair of needle roller, a group of optimized cycloidal parameters are obtained through the comparative calculations w...
研究了活齿端面谐波齿轮各啮合副齿面修形的原则，得出了波发生器、活齿前后端和端面齿轮齿面的修形高度之间必须满足的关系。
The modification principle of tooth surface is deduced, and it draws the conclusion that the modificative tooth depth of wave producer, end face gear and oscillating teeth have certain relation.
齿轮A位于驱动轴的末端，齿轮b在副传动轴上，它们恒定啮合。
Gear a, at the end of the drive shaft, and gear B, on the countershaft, are in constant mesh.
提出一种新的计算圆柱蜗杆副啮合的数值计算方法。
A new numerical computing method suitable for all kinds of cylindrical worm gearing is proposed.
由于齿轮副啮合刚度的影响，动力学方程序代表了一个具有时变系数的线性动力系统。
Because of the meshing stiffness of a gear pair, the governing equation denotes a linear dynamic system with periodic time-varying coefficient.
齿面修形是提高齿轮副啮合性能的重要手段。
The modification of gear is a principal method for improving performance of meshing.
提出利用高精度测角仪测量齿轮副在啮合过程中不同啮合位置时轮齿受载综合变形的新方法。
In this paper, a new method to measure meshing composite deflections of loaded cylindrical involute helical gear by using high precision clinometer is presented.
通过锥蜗杆传动副的啮合分析，用当量圆柱蜗杆副的分析方法，得出阿基米德锥蜗杆副的装配条件。
This paper makes a meshing analysis about the spiroid gearing. Using the method of equivalent worm gearing, the assembly condition of Archimedes spiroid gears has been obtained.
根据这一振动模型，推导了齿轮副的平均单齿刚度、单对轮齿啮合综合刚度、有效质量、固有频率与临界转速等一系列计算公式。
The model is used to understand a series of formulae, for example, mean single tooth stiffness, gear pair mesh synthesizing stiffness, effective mass, nature frequency and critical rotating speed.
齿面修形是提高齿轮副啮合性能的重要手段。
The modification of gear is a principal method for improving performance meshing.
确定双内啮合渐开线行星齿轮减速器内齿轮副的设计参数，从制造到安装有许多限制条件。
To determine the internal gear pair design parameters of two-stage internal contact involute planet gear reducer all constrained conditions from machining to assembly must be satisfied.
渐开线少齿差齿轮副，由于是内啮合，齿轮副的齿对之间的间隙很小，在受力后轮齿变形而使得同时有多对齿啮合。
As the gap of teeth of internal matins gears with small tooth number difference is small, several teeth will mate simultaneously after the teeth are deformed by load.
基于微分几何和空间啮合理论，分析了修正型圆环面双包络环面蜗杆副齿面形成原理。
Analysis of the forming principle of tooth flank of modified type worm gear pair was based on different geometry and spatial engaging theory.
运用傅立叶级数的形式，计算了一对宽斜齿轮副的瞬时啮合刚度及一对啮合轮齿的啮合刚度；
The mesh stiffness of a pair of helical gears is calculated by substituting the variance of the contact line length for the variance of the instantaneous mesh stiffness.
在机构强度分析中，阐述了凸轮-针轮副啮合齿面接触强度、针齿销的弯曲强度计算和刚度计算。
Not only the contact strength between the CAM and the rollers is discussed, the flexural strength and rigidity of the rollers are also discussed.
其结论是建立该类齿轮副承载啮合性能分析计算方法的基础。
Thus, the basis of founding loaded tooth contact analysis calculating method of hypoid gear is brought about.
我们将齿轮啮合过程中因多齿啮合而导致齿轮副承载能力提高的现象称为弹性啮合效应。
The phenomenon of increased loading capacity caused by several contact teeth is called Elastic Meshing Effect (EME).
为了提高面齿轮副的强度并解决其磨齿问题，提出了弧线齿面齿轮副的一种新的加工方法，并研究其啮合特性。
To improve tooth strength and make tooth grinding implement for face gear, a new generating method of face gear drive has been proposed, and the meshing characteristics are investigated.
基于齿轮副的动态啮合模型，对具有误差激励的齿轮副按长、短周期从理论上研究了其动态响应特征。
The paper researches the spectrum characteristics of dynamic response of the gear pair with the error excitation in the long and short period based on dynamic mating model of the gear pair.
平面包络环面蜗轮副具有优良的啮合性能，它是一种具有广阔应用前景的传动形式。
Worm pairs of planar envelope hourglass have many advanced meshing properties and potential applications.
按上述原理设计加工出的谐波传动齿轮副能够符合齿廓啮合基本定理。
The harmonic drive gear pair which are manufactured on the principle of "Converted Engagement Reappearance" can conform to the Willis theorem.
交错轴斜齿轮啮合原理广泛应用于齿轮加工及测量，其特点是齿轮副满足点啮合原理。
The crossed helical gear engagement principle is applied to gear machining and measuring widely. The crossed helical gear pair meets the point engagement principle.
各齿轮副均采用优化细长齿轮，并进行强化喷丸，有效降低啮合噪音、提高承载能力。
The gears adopt optimum design of fine-depth teeth and shot peening treatment in order to decrease noise if gearing and increase the capacity.
各齿轮副均采用优化细长齿轮，并进行强化喷丸，有效降低啮合噪音、提高承载能力。
The gears adopt optimum design of fine-depth teeth and shot peening treatment in order to decrease noise if gearing and increase the capacity.
应用推荐