检查确认吸料软管有没有顶在料桶壁上。
Check that the suction hose does not press against the feeding tank.
稳定高效吸料系统，全自动送料、补料；
Stable high-efficiency material suction system, which enables fully-automatic material feeding and replenishing;
吸料机在输送热料时，料管需选配耐160度高温料管。
Heat-resistant(160) pipes should be used when conveying hot material.
自动比例阀配置，混料均匀，配合吸料机使用，可达立即回收效果。
Auto ratio valve unit to make mixing evenly used together with material drawer, recovery effect is good.
逆时针转动后单向节流阀手柄，气缸后退速度加快，吸料速度也加快。
When the level of the rear one-way throttle valve is turned counterclockwise, the backward traveling speed of the cylinder and sucking speed increase.
尽可能使吸料管处于倾斜状态，避免盘曲使用，否则会影响送料功能。
Try to make the material sucking tube in a slant positing and avoid zigzags which will affect the transmission performance of the machine.
可加装自动比例新旧料混合，并配合吸料机运作，达到自动化生产立即回收效果。
Can be equipped with automatic proportion and mixing, and together with the material sucking machine, automated production to achieve the effect of immediate recycling.
本文对挤塑机吸料系统的故障原因进行了分析，提出了一种简单有效的解决方法。
The trouble causes for an extruder suction system are analyzed in this article and a simple and effective solution is submitted.
文章描述了矿用起重机的功能及各组成部件主要结构和吸料系统设计的理论基础。
This paper describes the new features as well as factories and mines with crane components, the main structure of the suction system design theory.
CMS2000层状剪切式填料轴封应用于负压进水的水泵时易产生吸料现象。本文对吸料原因进行分析，并提出改进措施，取得了较好的效果。
The seal of CMS2000 sheared packing can absorb charge easily to minus-pressured intake pump. Satisfactory result has been got by analyzing the reasons and making improvement.
由于转速过高，使高粘度泵在运转时内部转子几乎只是形成了空转，围绕所输送介质打滑，造成吸不上料，或者是流量很小。
Due to high speed, high viscosity pump inside the rotor is barely formed when running idle, surrounding medium by sliding, cause not feeding, or flow rate is small.
主要是提供电磁铁的直流电源及完成(吸、放料)控制要求。
The main purpose is to provide DC power supply and complete (suction, discharge) control requirements.
回吸量太大：气泡，焦斑，料垫不稳。
Too much retract: Air bubble, burns, and unstable melt cushion.
设有风量调节器，入料口变排风为吸风，能集中除尘，防止污染。
It also has wind volume adjuster to change the wind of inlet from emitting into inhaling, which make sure it can deduct collectively to prevent environmental pollution.
料浆愈稳定，生坯密度愈高，微观结构愈均匀，但吸浆速度减慢。
The higher the suspension stability, the higher the green density, and the more homogenous the microstructure, but the smaller the permeation rate.
该设备主要由以下部分组成：进料系统、筛体、机架、驱动系统、出料装置，垂直吸风道(选择件)等。
The equipment is mainly composed of the following components: feeding system, sieve, machine rack, driving system, discharging device and vertical suction duct (optional).
机床机身、送料。进给拖板等均为铸铁件，刚性高。具有吸振、抗震性好等优点。
The body, charge and feed slides, and other components of the machine tool are made of iron castings, which have high rigidity, good vibration absorbency, earthquake resistance, and other advantages.
怀疑吸嘴在吸取芯片的时候存在偏差，然后在焊接的时候真空漏气，最终导致了锡料被吸到芯片表面。
I suspect there is a deviation in the draw nozzle chip time, and then when welding vacuum leak, resulting in a tin material is attracted...
切割完成后小车前进至吸顶机位置停止，由真空风机吸除坯体上部底料。
The trolley stopped when it move to the device which cleaning up the waste on the top of base body by the vacuum.
切割完成后小车前进至吸顶机位置停止，由真空风机吸除坯体上部底料。
The trolley stopped when it move to the device which cleaning up the waste on the top of base body by the vacuum.
应用推荐