在合金分析及同位素密度成像系统中,采用本脉冲幅度分析器进行高速数据采集,取得了满意的效果。
In the alloy analysis and the formation system of image of isotope density. It has adopted the pulse range analyzer to gather the high-speed datas and obtained the satisfactory effects.
用微分热分析-液淬法研究几种常用合金元素对奥氏体枝晶形成与长大形态的影响。
The effect of some common alloying elements on austenite dendrites forming had been analyzed by differential thermal-liquid quenching analysis.
采用极化曲线测试结合扫描电子显微镜分析技术,研究了退火对铝合金阳极的活性的影响。
The effects of annealing on the activity of al alloy anode were studied by measurement of polarization curves and analysis of SEM.
本文叙述了利用基本参数法校正源激发合金元素荧光分析的基体效应的基本原理、基体效应的修正方法。
The fundamental parameter method of X-ray fluorescence analysis has many advantages, such as no concentration range limitation of elements, dispensability of standard samples and so on.
研究了该聚合物合金材料的增韧机理,并分析其性能与结构的关系。
Toughening mechanism was studied, and the relationship between properties and the structure was analyzed.
通过对频响曲线的对比分析,得出阻尼材料复合铝合金型材隔声的效果。
The effect of aluminum alloy materials on noise insulation with damping materials can be got.
用显微硬度仪测定合金的硬度,分析其硬度随氧化时间变化的情况,绘制该钢的显微硬度随时间变化的曲线。
The hardness of the alloy following the change of time was analyzed by micro- hardness instrument and the alloy's hardness curve following the change of time was drawn.
以分析起重机油箱上体工艺特性和设计其低熔点合金拉深模具结构为例,论述了低熔点合金冲压模具的结构特点及优势。
Though the analyzing of the upper part of oil box and the designing of the structure of the die, the article discusses the characters and advantage of the low melting point alloy die.
利用形核理论,对大块非晶合金的形成条件、控制因素、合金成分设计思路、制备原理与技术等进行了分析与讨论。
Forming conditions, control factors, alloy design methods, manufacturing principle and technology of bulk amorphous alloys are analyzed and discussed using nucleation theory.
本文通过对电阻点焊电极电压动态特性的分析,研究了低碳钢及低合金高强度钢电阻点焊的质量问题。
The quality of resistance spot welding of low carbon steel and high strength low alloy steel is studied by looking into the dynamic voltage characteristics of the electrodes.
介绍了测量铝硅合金变质处理效果用热分析仪的硬件、软件设计及实际应用。
This paper introduces the design of hardware and software of a thermal-analysis meter for measuring Al-Si alloy modification effect, and discusses its application.
因此,确定电解浸蚀法作为铜铬稀土合金定量金相分析的试样制备方法是切实可行的。
Consequently, it is feasible to determine electro-etching method as the sample preparation method about quantitative metallographic analysis in CuCrRE alloy.
分析了该合金在试验参数范围内变形的应力-应变曲线特征。
Characteristics of stress strain curves of the alloy deformed with the test parameters were analyzed.
用俄歇能谱aes分析了合金钝化膜的组成。
分析了高温合金孔加工的技术难点。
Technical difficulties of high temperature alloy hole have been analyzed.
研究分析了合金过渡层与金属基体接合界面组织结构。
The microstructure between alloy transition layer and base metal has been studied.
根据实验结果,提出了利用看谱镜对钛合金中的锡、铁元素进行光谱分析及牌号鉴别的方法。
Based on experimental results, spectroscopic methods are presented for analyzing spectra of Sn and fe in Ti-based alloys and for identifying different kinds of Ti-based alloys.
在合金焊接性分析的基础上,探讨了相应的焊接方法、焊接材料和焊接工艺措施,并进行了试板的焊接。
Based on the analysing weldability of the alloy, the welding method, material and procedure are chosen and the alloy plates are welded.
通过对新型铝合金时效处理后的组织结构进行分析,研究了不同的时效温度和时间对该铝合金力学性能的影响。
The effect of aging temperature and aging time to new-type heat-resisting aluminum alloy forging structure and properties are introduced.
分析了镁合金ECAP加工技术的试验和模拟方案。
Routine of experiment and modeling for ECAP of magnesium alloys was schemed.
分析了制备合金的组织和性能特点。
分析了制备合金的组织和性能特点。
应用推荐