输送皂角泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力最小，因此轴承负荷小，磨损小，泵效率高。
Pump is the drainage and back into the groove of reasonable design, is a gear in the work under the minimum torque force, so the bearing load is small, wear small, pump with high efficiency.
重新调整后，解决了该车轮胎异常磨损问题，并确认该车的设计参数是合理的。
After the readjustment, the problem of the abnormal wear of tyre was solved, and the passenger car's design parameter is firmly reasonable.
汽车转向梯形机构的设计在汽车设计中占据重要的地位，合理的设计可以减小车轮在转向过程当中的滑动，使轮胎的异常磨损控制在允许的范围内。
The design of Ackerman geometry plays a very important role on vehicle design, reasonable design could reduce the slipping in turning, make the abnormal wear in a permissive range.
文章根据皮碗式清管器在钢质管道中的运行特点，分析了影响清管器皮碗的特性及磨损因素，给出了皮碗合理过盈量。
The article analyzes characteristics and abrasion factor of leather cap type pig according operation feature, and then proposes reasonable magnitude of interference.
提出了合理选择立轴平面磨削方式的依据，以利于提高磨削效率，降低砂瓦磨损。
Some propositions are given for reasonable selection of grinding ways in order to extend grinding efficiency and reduce abrasive segment wear.
这是因为，合理的预热能够协助机油在发动机部件与部件之间构成“油膜”，然后削减发动机部件磨损。
This is because a proper warm-up can assist the oil to form an oil film between the engine parts and components, and then reduce the wear of engine parts.
汽车离合器在实际使用过程中，希望能预测出一定条件下工作的零件的磨损值，以便于控制零件的磨损和制订合理的维修期限。
It is expected that the wear value of automotive clutch part used in certain condition can be predicted to control the part wear and determine the reasonable maintenance and repair time.
研制了一种利用滚柱并通过楔形结构实现制动增力的新型增力式车轮制动器，该结构可使制动蹄受力合理、磨损均匀，为中、重型汽车采用液压制动提供了有效的途径。
A new type of servo brake which provides a increased brake torque by a roller and a wedge structure, whose advantages are its ideal force on brake shoes and even wear, has been developed.
该模型综合了目前较为合理的研究成果，客观地反映了鼓泡床中埋管磨损的基本规律。
It gathers up the present results on reasonable studies, and shows objectively the fundamental rules on erosion of horizontal tube immersed in fluidized bed.
老化磨损、可靠性差、灾害事故、使用环境、不合理储存、人为因素等都是引发教育装备发生故障的原因。
Aging wear, poor reliability and disasters and accidents, use environment, unreasonable storage, human factor etc cause of education equipment failure.
泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力最小，因此轴承负荷小，磨损小，泵效率高。
Pump is the drainage and back into the groove of reasonable design, is a gear in the work under the minimum torque force, so the bearing load is small, wear small, pump with high efficiency.
研究结果表明，选取合理的工艺参数能提高工件表面精度和减少刀具的磨损。
The results show that reasonable process parameters are help for better surface integrity of machined workpiece and decrease wears in the tool.
泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力最小，因此轴承负荷小，磨损小，泵效率高。
Pump discharge of oil with reasonable design, gear oil and back at work under minimum torque force bearing load, so small, wear small, pump with high efficiency.
根据在高温氧化性气氛下磨料磨损的工况条件，合理设计了抗磨耐热钢材料的组织和化学成分。
According to the working condition of high temperature and abrasive wear, the material structure and composition of the wear-resistant and heat-resistant steel are designed.
阐述了气门座圈的工作环境和磨损机理，高品质气门座圈的关键在于恰当的材料选择和零件的合理设计。
The paper explains the working environment and wear mechanism of valve retainer. The key factors for superior valve retainer quality are the proper material selection and reasonable part design.
常见的电动机轴颈磨损原因：装配不合理、键装配不合理、电动机轴承损坏。
The usual reasons of abrasion of electric motor crankshaft are in the following: unreasonable assembly, unreasonable key assembly as well as the spoilage of electric motor bearings.
探讨了硬度对钢蜗轮副材料磨损特性的影响，为研究钢蜗轮副合理的硬度配对提供试验依据。
The influence of hardness difference on the wear behaviour of steel-steel worm gear's material is investigated, which provides a foundation for proper hardness matching.
文中还根据配油盘表面的磨损形貌，找出了合理选择配油副材料的依据。
In the light of surface morphology of oil-distributing pair a criterion for selection of optimum material of oil-distributing pair is found.
泵内有设计合理的泄油和回油槽，是齿轮在工作中承受的扭矩力最小，因此轴承负荷小，磨损小，泵效率高。
There are well-designed pump drain back tank and is exposed in the work gear torque exerted the smallest, so bearing loads of small, wear, pump efficiency.
研究结果表明，采用合理的初始辊形可以一定程度上弥补轧辊磨损和热变形对带钢断面的不良影响，大大优化了带钢断面形状。
Research results show that bad strip profile caused by wear and thermal crown of roller may be properly repaired by sound original roller contour, and strip profile is greatly improved.
研究结果表明，采用合理的初始辊形可以一定程度上弥补轧辊磨损和热变形对带钢断面的不良影响，大大优化了带钢断面形状。
Research results show that bad strip profile caused by wear and thermal crown of roller may be properly repaired by sound original roller contour, and strip profile is greatly improved.
应用推荐