从而将模具能调整到预期的工作状态，生产出合格零件。
Thus the mold can be adjusted to the expected conditions, to produce qualified parts.
在以生产出合格零件为前提的条件下，胀形复合度有极限值存在。
Under the condition of producing qualified parts, the compound degree of stretching is limited to some extremity.
最后，在上述研究基础上对薄壁零件的电铸加工工艺进行了大量试验并制作出了合格的薄壁零件。
On the basis of these studies, the process of the electroforming complex thin-walled parts has been researched and qualified parts are got.
按照公司的图纸、检验指导书等完成零件检验工作，确保检验的零件质量合格。完成检验记录。
Implement incoming inspection according to the component drawing, inspection instructions, etc. and ensure the inspected components are qualified. Finish inspection record.
对以前提交零件不合格的纠正；
介绍了零件在加工过程中出现误差之后，如何用公差原则来判断其合格性，并通过实例给出了公差原则的公式化表述方法。
This Paper describes that how to use tolerance principle to identify the qualified problem of spares after the spares show error in the process through examples.
经过CAE拉伸软件的模拟分析，对于拉伸不足的区域采用增加拉伸筋的方式，通过试模最终加工出合格的零件。
By the simulating analysis to CAE drawing software, adding draw bead restraining mold is applied on the area of deficient stretching, the eligible products are produced finally by die testing.
经过CAE拉深软件的模拟分析，对于拉深不足的区域采用增加拉深筋的方式，通过试模最终加工出合格的零件。
Through simulated analysis of CAE simulation software, It applies drawing ribs to insufficiently drawing area. It produces qualified parts through testing die.
通过实验成功验证了该零件挤压成形的可行性，挤压出来的产品尺寸精度和表面精度均合格。
The extrusion forming feasibility of the component was confirmed by experiment. The size precision and surface roughness of the products are qualified.
轭铁是控制元器件中较关键的零件，具有精度高、加工困难，对工人的操作技能有较高的要求，零件合格率低等特点。
Yoke steel is the key part in controller, the precision is high, manufacture is difficult, has high request to the worker's operation skill, the component qualified rate is low.
指出铸造的毛坯件不合格及零件本身强度不高是产生裂纹的主要原因。
Pointing out the main reason of crack formation is that casting blank is not up to standard and the strength of parts is not enough.
批量生产证明，采用电化学法退除钼层工艺可处理各种喷钼层不合格的零件。
Practice indicated that using electrochemistry treatment to remove molybdenum layer can handle the problems for those parts with unqualified molybdenum spraying layer.
并对其原因进行了分析。采取有效措施解决了焊接破裂问题，使焊接零件完全合格。
Effective measures were taken to solve the problems of rupture, made all of the welded parts up to standard.
介绍了一种防止移动节零件装错的装置，可确保零件装配后100%合格。
One kind of plunging joint assembling POKA YOKE is introduced, with this POKA YOKE, the assembled parts can be guaranteed 100% qualified.
分析了零件模糊合格事件、零件模糊不合格事件、零件可修复模糊不合格事件和零件不可修复模糊不合格事件之间的关系。
The relations among the fuzzy qualified event, the fuzzy unqualified event, the mendable fuzzy unqualified event and the non-mendable fuzzy unqualified event of the parts are analyzed.
结合数值模拟，提出了零件工艺性的改善措施，获得了合格的零件。
Combined with numerical simulation, the improvement measures of parts manufacturability is proposed and the qualified parts are gained.
利用设备自己动手对零件的实体加工并加工出合格的零件。
The use of equipment for the do-it-yourself parts processing entities and a qualified parts processing.
在机械零件的切削加工和检验中，可能出现伪不合格品。
There may be pseudo_unqualified products during the course of mechanical cutting.
摆轮是手表的主要零件，由于它尺寸小，精度要求高，一般说来，它的产品合格率较低。
The balance wheel is the main part of a wrist watch. However, now its percent of pass is relatively low in our watch industry because of its small size and high precision.
泵在主要零件材质、制造精度、装配精度检验和液压试验合格后，方能进行试运转。
Pump in the major parts material, manufacture, assembly precision accuracy test and hydraulic test after passing the required test run.
泵在主要零件材质、制造精度、装配精度检验和液压试验合格后，方能进行试运转。
Pump in the major parts material, manufacture, assembly precision accuracy test and hydraulic test after passing the required test run.
应用推荐