针对这一问题,本文研究了零件加工误差对动模板合模位置的影响,得出了零件加工误差的许用值范围,并计算了由于销轴摩擦力对合模力放大比的影响关系式。
Aiming at these problems, this paper studies how the original error affects the accuracy, works out its allowable values, and finds out the equation between friction of pins and clamping force.
本文介绍采用功率键合图和状态空间法对薄膜反馈节流液体静压轴承的动状特性进行数字模拟的方法;
This paper describes an approach using power bond graph and condition space method to digitally imitate the dynamic characteristics of the hydrostatic bearings with film feedback throttle.
本文介绍了功率键合图的基本概念,以直动式溢流阀为例,讨论了键合图的建立、状态方程的建立、液压系统动态响应的数字仿真方法。
This article introduces the fundamental concept of power bond graphs, and discusses how to establish bond graphs, status equations, and digital simulation of dynamic responses in a hydraulic system.
压电层合结构尤其是层合状压电致动器,多在内电极端部发生断裂。
And multilayer piezoelectric structures especially multilayer piezoelectric actuators often failured from the edge of internal electrodes.
采用ANSYS软件对前、后固定模板及动模板的挠度进行了有限元计算,进而求解了合模机构的系统刚度及临界角。
Utilize ANSYS to compute deflection of the each of moldboard stroke in infinite elements' method and then solve the systematical stiffness and the critical Angle of clamping unit.
本机合模装置属液压式结构,主要由导柱、动模板、支承板、锁模油缸等组成。
This device adopts hydraulic structure and is mainly made up of guide pole movable platen support plate and clamping cylinder etc.
运用键合图理论建立了系统的数学模型,并利用计算机仿真技术对系统的动特性进行仿真分析。
Mathematic model of the system was established by bond graph theory, and then the simulation analysis on dynamic characteristics for it was worked out by computer.
波罗马康尼产品包括用于地铁、巴士、动车和高速列车的车载天线,合路器及滤波器。天线内置放大器和高压保护。
Polomarconi Telsa SpA scope of products is on-board antenna for metro, bus, EMU and high speed train. The antennas with embedded amplifier and high voltage protection.
结论稳定牙合垫对夜磨牙患者的牙齿磨动有所改善,但对于睡眠结构和睡眠微觉醒的发生无影响。
Conclusion the stabilization splint is effective for treating sleep bruxism in short term, but can not affect the sleep structure and the incidence of micro-arousal.
卷筒止动件(33)沿所述一侧壁的壁面移动,可与嵌合于所述轴承部的卷筒支承件(27)卡合。
A reel stopper (33) moves along the wall surface of the one side wall and can engage with the reel receiver (27) fitted to the shaft receiving portion.
所述合模装置包括合模架、和设置在合模架上且位于圆盘下方的合模油缸,所述合模油缸活塞可上下往复移 动;
The molding device comprises a molded rack and a molded fuel tank positioned on the molded rank and under the disk. A molded fuel tank piston can be moved up and down.
检验了坍落度、动性、合强度和氯离子扩散作用。
Slump, slump flow, comprehensive strength and chlorine diffusion are tested.
油缸(5)推 动的方向与挤气滚筒(2)和双层合卷滚筒(1)的轴心连线相平行。
The driving direction of the oil cylinder (5) is parallel to the connecting line of shaft centers of the air extruding roller (2) and the double-layer roll combining roller (1).
波罗马康尼产品包括用于地铁、巴士、动车和高速列车的车载天线,合路器及滤波器。
Polomarconi Telsa SpA scope of products is on-board antenna for metro, bus, EMU and high speed train.
波罗马康尼产品包括用于地铁、巴士、动车和高速列车的车载天线,合路器及滤波器。
Polomarconi Telsa SpA scope of products is on-board antenna for metro, bus, EMU and high speed train.
应用推荐