拖到绘图页后,可以添加可编程逻辑控制器。
可编程逻辑控制器PLC在工业控制中应用广泛。
可编程逻辑控制器(的PLC)已广泛应用于工业。
Programmable Logic Controllers (PLCs) have been widely used in industry.
整个系统是以可编程逻辑控制器为核心,辅以其它设备构成。
This system is made of Programmable Logical Controller and other assistant device.
介绍可编程逻辑控制器(PLC)在电站制粉系统程控中的应用。
This paper introduces the application of programmable logical controler PLC to program control of coal pulverization.
该可编程逻辑控制器具有配置简单、扩展方便和造价低廉等优点。
It has advantages of simple configuration, easy extending and lower cost etc.
可编程逻辑控制器简称为PLC,它是以单片机为核心的工业控制专用机。
Programmable logic controller is short for PLC. It is a special purpose industry control machine, that kernel is single chip microcomputer.
加速器磁铁电源的逻辑保护和控制一般通过可编程逻辑控制器PLC实现。
For the accelerator magnet power supply, usually the Programmable logic controller (PLC) is used to server as the controller for logic protection and control.
对于底层数据的采集本文使用了西门子公司的S7-300可编程逻辑控制器。
This paper uses the S7-300 programmable logic controller of Siemens to collect the bottom data.
安装,故障排除和维护动力传动,真空,液压和气动系统以及可编程逻辑控制器。
Install, troubleshoot and maintain power transmission, vacuum, hydraulic and pneumatic systems, and programmable logic controls.
该系统采用IEEE488总线和可编程逻辑控制,大大提高了系统的自动化程度。
The system adopts the IEEE488 bus and PLC control, greatly improves its automation.
HSP系列玻璃喷砂机自动控制系统由触摸屏和可编程逻辑控制器(PLC)组成。
HSP series glass sand blasting machine automatic system is made of touch screen and PLC.
该自动化系统分为信号监测、PLC(可编程逻辑控制器)控制、上位机控制三大部分。
The system is composed of three subsystems, they are the signal monitor subsystem, the PLC (the Programmable Logical Controller) one and the host computer control ore.
文章主要是采用西门子公司的可编程逻辑控制器PLC- 200来实现交通信号灯的控制。
In the paper, traffic signal light is controlled by PLC-200 by using programming logic controller of Siemens company.
适用于牛奶、乳酸奶、豆奶、果汁饮料等饮品类的生产包装,该机设计合理,可编程逻辑控制光电气动。
It is suitable for the packing of drinks, such as milk, sour milk, and soy milk, fruit juice. The machine has a reasonable design, can compile discharging pneumatically.
本文依托于变频调速器和可编程逻辑控制器(PLC)技术,可以有效的把智能控制方法应用于控制现场。
The system is based on frequency conversion velometer and PLC. This paper analyses the construct of the system, and introduces the working theory of position and graphic sensors.
介绍了一种由水界面检测传感器、油界面检测传感器,通过可编程逻辑控制器(PLC)控制的新型浮油回收机。
This is a new floating oil recovery equipment which consists of the water interface testing sensor, oil interface sensor, and is controlled by PLC.
介绍了现代雷达对系统监测和控制的要求,及如何利用可编程逻辑控制器(PLC)来实现现代雷达监测和监控系统。
This paper introduces the requirement of modern radar for monitoring and controlling, and how to use the PLC technique to carry out the monitoring and controlling in modern radar system.
分实时和非实时两部分设计一个基于IEC61131 - 3标准的可编程逻辑控制器(plc)梯形图检查模块。
A diagram checking module for PLC base on IEC61131-3 standard is designed and the module is divided into real-time part and non real-time part.
介绍了可编程逻辑控制模块在自动运输线控制系统中的应用,对系统的控制功能及实现方法做了说明,并给出了功能块图。
This paper introduces the application of the universal logic module on automatic conveyor belt control describes and presents the main functions of the system, solutions and soft circuit diagram.
为了排除人为干扰、提高可靠性,采集数据以可编程逻辑控制器为核心,通过现场总线和以太网的多层网络传送至数据库中。
To avoid interfering by work, data were sampled through a multi-layers network which synthesize the field-bus and Ethernet and center on programmable logic controller.
通过基于稳态视觉诱发电位构造的脑-机接口获取控制指令,通过可编程逻辑控制器(PLC)控制机械手完成规划的动作。
We could obtain dictates in the steady-state visual evoked potential (SSVEP) and can control the spatial movement of the artificial limb through a programmable logic controller (PLC).
针对西安电子科技大学MOCVD系统,根据MOCVD系统工艺要求,进行了基于可编程逻辑控制器的MOCVD设计与研究。
According to the characteristics and requirements of Xidian Univ. MOCVD system, a research and design about the MOCVD control system based on programmable logic controller are carried out.
主要介绍电气设备中可编程逻辑控制器(plc)、变频器、触摸屏、RS- 485模块及个人电脑之间实现异步通信的软切换。
The soft switching of asynchronous communication among PLC (Programmable Logic Con-troller), transducer, touch screen, RS-485 module and PC is introduced.
利用S5-95U可编程逻辑控制器开发的95U炉控系统及炉控人机操作界面,优化了控制结构,使加热系统安全运行,收到了良好效果。
The 95U heater control system and its MMI developed from S5-95U optimizes the controlling structure, which makes the operation of heating system safer.
针对目前我国机载航空电子设备特别是重心控制设备的落后现状,设计一套基于工业控制计算机和可编程逻辑控制器的飞机重心自动控制系统。
This paper develops a set of barycentre of plane automat Ed control system based on industrial personal computer and programmable logic controller aiming at the defect of avionics in our country.
该文介绍了西门子全数字直流调速装置(6ra70)和可编程逻辑控制器(SIMATICS7- 300)首次在码垛电磁铁系统中的应用。
This paper introduce the application of Siemens digital direct current timing device (6ra70) and program logical controller (SIMATIC S7-300) in piling bed electromagnet for the first time.
介绍了造纸配浆工段的工艺流程、测控系统、以可编程逻辑控制器(PLC)为控制单元的系统结构和硬件设计,同时详细阐述了实现连续配浆的控制算法。
The paper introduces the process of continuous furnish preparation, its measuring and controlling systems, the structure and hardware design of the whole system where the PLC is used as control unit.
介绍一种基于可编程逻辑控制器(PLC)和触摸屏(PT)的自动切筋沾锡机及PLC和PT的应用与设计思想,讨论该系统的结构、工作原理和软件设计。
An automatic trim and solder machine based on PLC and PT are introduced, and application and designing method of PLC and PT are presented.
介绍一种基于可编程逻辑控制器(PLC)和触摸屏(PT)的自动切筋沾锡机及PLC和PT的应用与设计思想,讨论该系统的结构、工作原理和软件设计。
An automatic trim and solder machine based on PLC and PT are introduced, and application and designing method of PLC and PT are presented.
应用推荐