本文以叠加法提供一个精确解。
This paper provides a rigorous solution by the method of superposition.
阐述了“叠加法”在材料力学中较广义的概念。
The generalized concepts on superposition method in mechanics of materials are elaborated.
用广义简支边这个概念及叠加法，就可以解这类问题。
By using the concept of generalized simply supported edge together with the method of superposition, we can solve this problem.
叠加法是由内标法衍生而来的一种气相色谱定量方法。
The addition quantitative method is derived from internal standard method.
本文以叠加法提供在弹性地基上的自由矩形板的精确解。
This paper presents an exact solution for a free rectangular plate on elastic foundation by the method of superposition.
针对无衍射光成像系统的成像特性，提出了多幅图像叠加法。
A multiple images superposition algorism is introduced based on the properties of the pictures imaged by the designed optical system.
应用模态叠加法研究了用粘弹性阻尼控制加筋板的稳态简谐响应。
The viscoelastic damping control of steady-state harmonic response of stiffened plate is studied by using modal superposition method.
为在计算中避免散斑去相关的影响，采用了逐级位移相关叠加法。
During the calculation of cross-correlation, a progressive correlation method was used to avoid the de-correlation caused by the object surface.
本研究探讨了耳机以叠加法和分离法传送双重听觉信号的知觉特点。
The perception features of double auditory signal transmitted by headphone with overlap method and separate method are discussed in this paper.
这种方法优于传统的能量法，力矩面积法，叠加法，差分法等方法。
It is shown that this approach much more efficient than the conventional one, such as energy method, moment-area method, method of superposition and finite difference method.
利用复数振型叠加法，这种求解方法能够得出结构动力响应的精确解。
The proposed approach can offer an exact solution for dynamic response of base-isolated structure, through using the complex mode superposition method.
对于转子系统非线性动力学问题，直接积分法比模态叠加法更为有效。
With regard to the nonlinear kinetics problems of a rotor system the direct integration method is more effective than the modality superposition method.
研究一种新的计算方法——以振型叠加法为基础的等效附加塑性荷载法。
A new calculation method, base the method of equivalent additional plastic loads on modes of vibration superposition method is studied.
本文在大量实验的基础上，提出了叠加法定量过程中应注意的一些问题。
Based on enough experiments, this paper points out some problems dealing with addition method.
因此，考虑平衡节点的电流叠加法较考虑平衡节点的灵敏度算法更优越。
Therefore, a slack bus consideration of the current superposition arithmetic is superior to a slack bus consideration of the algorithm based on the sensitivity theory.
同时，还提议用叠加法来解释铸锭的结构，并提出了某些抑制柱状晶的想法。
It also proposes to make use of the superimposing method to explain the structure of ingots and provides some clues for restraining the columnar growth.
在此基础上，提出了利用空间—时间(滤波)叠加法实现向真动校正叠加的逼近。
On that bases, the paper presented using space-time (filtering) stack approach to realize approaching to true NMO stack.
分别采用直接法和模态叠加法，计算声场-结构耦合系统的声压响应水平及其敏度。
The modal frequency response and its sensitivity analysis for the coupled system using the direct method and the eigenmodes.
本文利用共地面点叠加法，通过迭代的方式逐步求取较为准确的转换波的静校正量。
In this paper, it exploit the method based on common ground point fold step by step to strike a more accurate conversion of wave static correction by iteration.
本文应用线性波理论，通过波浪叠加法，探讨了海洋平台油气生产立管系统的动力性质。
In this paper, linear wave theory and wave superposition method are used to study dynamic behavior of oil or gas production risers on the offshore platform.
通过分析系统图像的噪声特征，采用多帧平均叠加法、邻域处理法，取得了较好的效果。
Aim at the characteristic of system image noise, using the algorithms of image noise filtering, multi-frame mean, neighborhood processing, we have obtained good results.
在设计复合材料结构时，可以在基材的负载基础上，根据叠加法则推算出复合膜的破坏载荷。
Composite films fracture load can be calculated with plus theorem based on the load of base material when design the structure of the composite material.
本系统电缆绝缘在线监测理论，以比较成熟的直流叠加法为主，加上直流分量法作为理论基础。
The DC superposition method was mainly utilized because it was ripe theory about On-line Insulation Monitoring on the XLPE power cable, in addition of the DC partial current method.
研究方法：建立了水树精确数字仿真模型，提出一种新的在线绝缘诊断方法：高频信号叠加法。
Research methods: in this paper, an accurate water tree model has been created. We have successfully developed a new hot-line diagnostic method called "high frequency superposition method".
分别计算了三种抗剪机制承担剪力的大小，由叠加法和杠杆法分别确定最终受剪、受弯承载力。
The shear of each model is calculated separately and superimposed to establish the shear bearing formula. The formula of bend is established by lever principle.
在精细时程积分法的基础上，将精细积分法与振型叠加法结合起来，提出振型分解精细积分法。
This new method is called the mode decomposition precise integration method because it is the result of the combination of the mode decomposition method with the precise integration method.
最后进行了动态分析，对冲击载荷进行了研究，采用模态叠加法对典型工艺的动态响应进行计算。
Finally, in dynamic research, the impulsive loads of the frame are studied and dynamic response of the typical process is calculated and analyzed with modal superposition method.
从产品已知条件出发，利用有限元、模态综合法和振型叠加法等理论，探索出求产品脆值的新方法。
Based on Known conditions of the product, by using the FE? Modal synthesis and vibration modal congruence theories, this article explores a new product frailty solution.
为模拟不规则波，采用了线性波浪叠加法。利用相关函数法进行谱估计，以检验不规则波造波效果。
Then the linear superposition method is used to simulate irregular wave, and is verified by the autocorrelation method of wave spectrum estimation.
为模拟不规则波，采用了线性波浪叠加法。利用相关函数法进行谱估计，以检验不规则波造波效果。
Then the linear superposition method is used to simulate irregular wave, and is verified by the autocorrelation method of wave spectrum estimation.
应用推荐