确定了该工艺极限变形程度的判断依据；
变形程度是影响片状组织球化的主要因素。
The deformation degree is the major factor of globularization.
焊缝区金属变形程度大是产生焊合纹的关键；
The large degree of deformation of the metal in the weld seam is the key caused the weld stripes.
分析了变形程度、打击速度与锻件密度之间的关系。
The relation between the deformation degree, blow speed and forging density was analysed.
在圆孔翻边过程中，变形程度是用翻边系数来描述的。
Deformation extent is described by burring factor in the process of round hole burring.
实验中发现衍射摇摆曲线能够反映金刚石的塑性变形程度。
We also found that the diffraction rocking curves can reflect the elastic deformation degree of diamond.
变形程度对拉伸温度影响小，变形程度的增大使拉伸力下降。
And reduction affects drawing temperature little and its increasing lowers drawing force.
评估在变形程度、持续时间和能量损耗参数这些情形上的影响。
The effect of these states on deformation magnitude, duration, and energy loss parameters was assessed.
成形零件微观组织大小不均，主要受成形温度及变形程度的影响。
The grain size of formed part is unequal due to forming temperature and deformation extent.
本文分析了位错胞的形成、特性及其变形程度对位错组态演化的影响。
This paper analyzes the formation and characters of dislocation patterns, and the effect of strain on the dislocation pattern evolution.
从而在理论上论证了静水应力和塑性变形程度对塑性致密化规律的影响。
Therefore, the effects of static hydraulic stress and Plastic deformation on Plastic densification can theoretically be Proved.
研究表明，增加变形程度和选择合适的轧制温度能提高复合板的界面初结合强度。
The results indicated that increasing the deformation and a proper rolling temperature may improve obviously the bonding strength.
最大下沉值是度量层状矿体（如煤层）开采引起的地表移动变形程度的重要参量。
The maximum subsidence induced by mining bedding ore(such as coal seam) is an important parameter for estimating the degree of surface movement and deformation.
结果表明，轧制变形程度和铝层加热温度都是影响复合板初结合强度的主要因素。
The results prove that the initial bonding strength mostly depends on total reduction and heating temperature of al.
依据数字图像成像理论，获得套管变形程度的定量解释，并输出定量解释结果报告。
We obtained quantitative interpretation of casing deformation and printed its report from digital imaging.
分析了立辊孔型内倒角半径对轧件切头尾量、轧件稳定段轧件边部变形程度的影响。
The influence of groove fillet radii of vertical rolls on cropping and margin deformation of slab were analyzed.
研究了变形速度，试验温度以及预先塑性变形程度对氢致表观屈服强度下降的影响。
The effect of loading rate, test temperature and pre-plastic deformation on hydrogen induced apparent yield stress reduction have been investigated.
在触击球的时候，因为硬的拍子变形程度不及柔韧的拍子，所以损失的能量也少一些。
Stiffer racquets don't deflect as much on impact, resulting in less power drain than a flexible racquet.
分析了变形方式和变形程度对大型锥环形锻件组织和性能的影响并制定较佳锻造工艺。
The effect of deformation mode and degree on the structure and properties of large conical ring forgings was analyzed. An optimal forging process was drawn up.
构造圈闭的平面展布主要受应力作用状况、构造变形程度和断裂发育状况等因素控制。
The plane distribution of the structural traps is controlled by stress, tectonic distortion and faults.
首先介绍了表征机匣变形程度的新参数，进而引进了非轴对称压气机模型的建模方法。
The new parameter representing the nonuniformity of tip clearance is recommended, and the modeling approach for the nonaxisymmetry compressor is introduced.
实验结果表明，宣纸具有随湿度变形的特性，变形程度与纸的纤维组成和干燥方法有关。
The results showed that the paper had the characteristics of dimensional unstability and the extent of deformation was related to the component and drying methods of paper.
提出了采用热扭转试验来模拟金属材料热变形时塑性变形程度与晶粒大小相互关系的方法。
The method of relationship between plastic deformation degree and grain size was put forward, when the thermos-deformation of metal was simulated by the thermos-torsion test.
而以往的流动应力模型主要考察变形温度、变形速度和变形程度，对位错密度的研究很少。
In the past years, the models of flow stress were mainly focused on deformation temperature, deformation speed and deformation degree, but seldom on dislocation density.
在汽车覆盖件的冲压成型中，可以利用的是板材在稳定变形阶段所能达到的最大变形程度。
In the stamping and forming processes of automotive covering parts, only the maximum deformability, which is reachable in stable deformation stage of sheet metal, can be made use.
当这种不均匀变形程度足以使土体连续性破坏时，则地裂缝便在沉降区应力集中的部位发生。
When the deformation caused by the inhomogeneous subsidence accumulates to the critical state of the soil, ground fissures will occur in the stress concentration positions.
本文讨论了在锻造过程中不同变形温度、变形程度、变形速度对高温合金组织和性能的影响。
In this paper, the influence of various deformation temperature, deformation degree and deformation velocity on structure and properties of superalloys in forging process was discussed.
记录了冷挤压过程中与不同变形程度相对应的挤压力，绘制了冷挤压过程的连续挤压力曲线；
And the extrusion force to different transfiguration degree was recorded to draw the continuous extrusion force curve during the cold-extrusion course.
记录了冷挤压过程中与不同变形程度相对应的挤压力，绘制了冷挤压过程的连续挤压力曲线；
And the extrusion force to different transfiguration degree was recorded to draw the continuous extrusion force curve during the cold-extrusion course.
应用推荐