技术特点：本生产线具有翼板与腹板自动对中组立、翼板变形矫正、焊板速度可调等功能。
Technical character:This machine can perform the centering and assembling of both flange and web automatically, straightening of flange deformation, welding speed adjustment.
以钢板对接为例，提出了焊接变形高效矫正法的两条途径，并将其应用于几种常见的焊接变形矫正中。
Two methods of welding distortion straightening technique are summed up from plate model and applied to some conventional welding distortion treatment.
研究了工件的变形形式，并依此提出三坐标测量数据的软件矫正法。
The mode of the distortion of workpiece was studied. A software approach for rectifying three coordinate measuring machine data was proposed.
对于变形、缺陷超过允许偏差的构件，应安装前，在地面进行矫正、修理，合格后方可安装。
For the deformation, the defect exceeds the allowable deviation of the component, should be installed before the ground correction, repair, qualified before installation.
检查构件有无存在变形，如有变形误差应予以矫正和修复。
Check whether there is any deformation of the component, if the deformation error should be corrected and repaired.
矫正脊柱变形，改善不良体态，促进身体健康成长。
Correction spinal deformation, improve the bad posture, promote body healthy growth.
研究了工件的变形形式，并依此提出三坐标测量数据的软件矫正法。
The form of distortion of work piece was studied, and the software rectification method of three coordinates measurement data was put forward accordingly.
提出了焊接过程中产生裂纹的控制方法及对焊后变形的矫正方法。
Controlling for the variables related, preventing the crriage from cracking during welding and correcting distortion for it after welding are discussed, too.
如有严重变形时应用手提切割机切割或用气焊切割、矫正，以保证钢筋端面垂直于轴线。
If serious deformation is occurred, the manual operated cutter or gas cutter to be used for correction to ensure the re-bar end surface perpendicular to the axis.
光电整纬机是一种能够对织物纬纱变形自动检测和矫正的自动控制设备。
The Photoelectric Abb-Finishing Apparatus is an equipment which can automatically measure and straighten weft abb distortion.
本文详细地阐述了采用火焰法矫正钢管弯曲变形，并取得了满意的效果。
A flame method to correct the bending deformation of a steel tube has been introduced in the thesis and has got satisfied effect.
本文介绍了该钢箱杆件的制造工艺及不需焊后矫正就能达到规范要求的变形控制措施。
Fabrication technology and deformation control measures, which can meet requirements of specifications without need of corrections after welding, for the steel box members are expounded.
分析了变压器油箱焊接时变形产生的原因，提出了预防焊接变形的措施，介绍了焊接变形的矫正方法。
The causes of deformation in welding of transformer tank and precautionary steps are expounded in this paper. Its correction methods are introduced.
研究了工件的变形形式，并依此提出三坐标测量数据的软件矫正法。
The form of distortion of work piece was studied, and the software rectification method of three coordinates measurement data was pot forward accordingly.
本文针对焊接机柜加工中产生的侧板波浪变形，提出了一种运用点焊产生的电阻热来矫正变形的新方法。
Being aimed at distortion of side plate for welding case of electronic equipment, this paper puts forward a new method to straighten distortion by using resistance heat which produced by spot welding.
机械矫正法：机械矫正法是利用机械力的作用来矫正变形，可以用手工锤击或机械压力。
Machine rectification: machine rectification is using machine power to rectify deformation, which can be taken by hand hammering or machine pressure.
牙龈变形是开发虚拟牙齿矫正系统的一个重要部分，如何逼真地模拟牙龈变形是一个很复杂的问题。
How to realistically simulate gum deformation is a very complicated and important problem in the development of Virtual Orthodontics Treatment System.
结论曲面断层摄影各部位变形失真率不同，这为指导临床工作，如颌骨畸形矫正术中截骨线位置的确定。
Conclusion Distortion at the different parts of the orthopantomograph is different, therefore, the result should be beneficial for the clinicians in determination of bone cut of orthognathic surgery.
介绍了变形严重的提升机闸盘采用“氧-乙炔焰”加热矫正的原理、工艺程序及其效益。
This paper introduced the principle, the process and the effect of the new technology of restoring the deformed brake plate of hoist by use of "oxygen acetylene flame".
弯曲变形，否则应作水火矫正处理。4围壁板垂向板缝咨询隔绝扶强材应大于75mm。
Bending deformation, or should be corrected to deal with fire and water. 4, Wai board raphe vertical wall joints should be larger than the distance to support the strong wood 75mm.
弯曲变形，否则应作水火矫正处理。4围壁板垂向板缝咨询隔绝扶强材应大于75mm。
Bending deformation, or should be corrected to deal with fire and water. 4, Wai board raphe vertical wall joints should be larger than the distance to support the strong wood 75mm.
应用推荐