确定岩体变形和强度参数最常用的方法有三种：原位试验法、经验关系法及数值分析法。
There are three kinds of methods to confirm the rock deformation and intensity parameters:in situ test, experiential relation method and numerical analysis method.
现场岩体承压垫板法试验是测量岩体变形特性参数应用最广泛的重要方法。
The in-situ bearing pad test is an important method for measuring rock mass deformation property parameters with wide applications.
基于岩石试件的卸荷试验，研究卸荷条件下岩石的变形、参数及破裂特征。
Based on unloading tests of rock samples, the deformation, parameters and fracture features of rocks under unloading are studied.
通过室内试验，研究了大坝土体动强度特性及动变形特性，确定了大坝土体动力计算参数。
According to the laboratory tests, the dynamic strength and deformation properties of the dam material are studied and its dynamic calculation parameters are also determined.
在试验基础上就一般强度船板钢热变形时奥氏体再结晶百分数及晶粒尺寸与工艺参数的关系进行了研究。
According to the experiment, the effects of rolling parameters on the extent of austenite recrystallization and grain size show a varying way in different temperature area.
通过镦粗工艺试验，确定了该材料的热变形工艺参数，并对其进行了等温模锻工艺研究。
The technological parameter of heat deformation was confirmed by the test of Upsetting technology, and the isothermal stamping was studied.
设计了铝合金铸轧工艺模拟的实验装置，研究了在该试验条件下，铝合金变形组织与工艺参数的关系。
An experimental instrument for simulating the roll-casting process was designed, and the effect of processing parameters on the microstructure of al alloy was studied.
在分析岩体的变形特性时，岩体变形模量是一个非常重要的参数，一般要通过现场试验来确定。
The deformation modulus of rock mass is an important input parameter in analyzing deformation, which should be determined by field tests.
对轮胎进行侧向激振试验得到轮胎的侧向模态参数，依据轮胎侧偏时印迹的几何变形及模态参数建模的思想，得到了侧向力分布。
The distribution of the tire side force was obtained by using geometric deformation of contact patch of cornering tires and the principle of modeling tire with experimental modal parameters.
根据原位压板试验确定的强度和变形参数计算筏板基础下地基的承载力，并采用集中力弹簧模型计算筏板各点的沉降。
Based on the deformation modulus from the in-situ plate loading test, the settlement of each point on the raft foundation was calculated using spring model with concentrating force.
试验所获应变分布表明，带孔件在变形过程中存在拉深和翻边两种变形趋向性，在模具参数和工艺条件完全相同的情况下，其可能的变形趋势与孔的尺寸有关。
The results showed that, there is a deformation tendency of drawing, and flanging and the tendency is related to, in the same parameter of die and the same technological conditions, the hole size.
分析了该合金在试验参数范围内变形的应力-应变曲线特征。
Characteristics of stress strain curves of the alloy deformed with the test parameters were analyzed.
基于试验结果，拟合出了考虑各关键参数影响的火灾下两跨连续梁边支座反力与梁跨中变形的计算公式。
Calculation formula of side support reaction and deflection in the mid-span of beams subjected to fire were obtained by fitting curves of experimental data considering each key factor.
为合理确定地基承载力和计算沉降的变形参数，对其地基承载力采用原位压板荷载试验确定，较大于原地质报告提供的承载力。
The bearing capacity of ground depends on the in-situ plate loading test, and it was found the in-situ results are larger than the values given in the report of geotechnical engineering exploration.
因此通过对该试验的数据进行参数分析，提出了一个变形计算公式中较合理的折减系数。
Based on the parameter analysis, a more reasonable reduction factor is presented in the deformation formula.
变形参数采用原位压板试验所确定的变形模量，变形模量为压缩模量的6倍。
The deformation moduli from the in-situ plate loading test were used to calculate the settlement, and they were 6 times of the compressing modulus.
在与国外同类试验成果以及室内大型动三轴仪试验成果的广泛比较后，给出堆石材料动力变形参数职值的经验范围。
After comparing widespreadly with the results of similar field tests abroad and large scale dynamic triaxial apparatus tests, the ran…
在与国外同类试验成果以及室内大型动三轴仪试验成果的广泛比较后，给出堆石材料动力变形参数职值的经验范围。
After comparing widespreadly with the results of similar field tests abroad and large scale dynamic triaxial apparatus tests, the ran…
应用推荐