结果表明，欧拉描述有限变形本构方程适合于铅的有限变形压缩规律的描述。
The results show that the finite deformation constitutive equations based on Eulerian configuration are suitable for the compressive finite deformation process of lead.
扭曲是在部件上施加旋转的扭力。通常使部件被切断，压缩和变形，扭转和扭曲同属于此类别。
Torsion is the use of rotational pressure (torque) on a component. Twisting and torque and included in this category. Causes shearing, compression, and deformation of components.
可使钢材承受更大的变形及压缩，可以加工更多更好地标准件，如台阶螺丝或变形量较大的螺丝等。
Can give the steel ability of the more deformation and compression, can process more and better standard parts, such as steps screws or other screws with large deformations, etc.
如果减震材料长时间在高度压力下会发生厚度逐渐减少的现象，这叫压缩变形。
Compressive Creep is the gradual loss of thickness that may occur if a cushioning material is.
破损因素是压缩空气过高、喷吹管歪斜、花板变形等因素构成，调整后即可防止破损。
The damage factor is too high, the compressed air blowing pipe deflection, flower plate deformation and other factors, can be adjusted to prevent breakage.
冲击力产生的结果是较难预料的，包括：碎裂，破损，变形或者被压缩。
Impact has a wide variety of results including fracturing, breakage, deformation, and compression.
利用热模拟压缩变形实验研究了Q 235碳素钢多道次热变形及后续处理过程的组织演变规律。
The microstructure evolution of Q235 plain carbon steel in multi-pass hot deformation was investigated by means of hot compression simulation.
利用非线性有限元法分析了密封条的压缩受力变形特性，根据结构力学原理对密封条横截面形状进行了优化。
Using nonlinear finite element method, the compression load deflection of the seal was analyzed and cross sectional shape of the seal was optimized.
压缩或伸展是变形一个物体的方式所以它显示了一个物体有多么硬。
Squash and stretch is a way of deforming an object such that it shows how rigid the object is.
结果发现：一羟基或羧基化合物能提高氟橡胶混炼胶的防焦烧性，并对压缩永久变形和拉伸强度等有一定的改善。
The results showed that the compound could improve the scorch safety the compression set and the tensile strength of fluororubber compound.
钨丝体积分数超过60%以后，压缩强度与塑性变形能力反而下降。
However, the compression strength and plastic deformation ability decreased when the volume fraction exceeded 60%.
当等效应变速率较大时，变形热效应对流动应力的影响相当显著，压缩过程基本上成为绝热过程。
While the equivalent strain rate is high, this influence is of importance and the compression process can be approximately considered as an adiabatic process.
例如，骨骼或如眼球类的东东等也许不会真正的变形很多，尽管可以压缩它。
For example, the skeleton or things like eyeballs etc may not really deform much, though the flesh around them may.
压实粘土浸水饱和后，压缩变形显著增加，抗剪强度和粘聚力则显著降低。
Soaking leads to a significant increase in compression deformation and a significant reduction in shear strength and cohesion.
研究了控制熔体结晶法制备的半固态zl101合金的压缩变形行为以及显微组织的变化。
Compression experiments were carried out to investigate deformation behavior and microstructure of semi-solid ZL101 alloy fabricated by controlled crystallization technique.
在刀具前倾面前的金属直接受到压缩，首先弹性变形然后塑性变形。
The metal in front of the tool rake face gets immediately compressed, first elastically and then plastically.
研究了不同的预应力锚固结构作用下，在不同弹性模量的破碎岩质边坡中产生的压缩变形和附加应力变化规律。
The slope surface compression deformation and subsidiary stresses change rules with different elastic modulus of crush rock slope under different prestressed anchorage structures were investigated.
高温–高含冰量冻土在外荷载作用下会产生较大的压缩变形，对路基稳定性产生极大影响。
The warm and ice-rich frozen soil under an outside load will generate relatively large compression deformation which greatly influences the stability of roadbed.
对油品有极佳的抵抗力，耐高温、耐候性均佳，但机械强度、压缩变形率及耐水性稍差。
Excellent resistance to oil, high temperature resistance, weather resistance are good, but the mechanical strength, compression deformation rate and water resistance is slightly worse.
采用高温水蒸气处理和加热处理固定大青杨木材压缩变形，并对两种处理结果进行比较。
The wood of poplar is compressed, then the compression deformation is fixed by high temperature steam and heating.
在单轴压缩变形破坏过程中，具有与普通岩石试件不同的四阶段性特征。
Moreover, the uniaxial compressive deformation and damage of thenardite are different from other rocks during four deformation phases.
水力劈裂过程只有弹性变形和脆性破坏，不存在裂隙压裂过程中的第三种变形机理—压缩破坏。
There are only elastic deformation and brittle deformation on the process of hydraulic fracturing, and not compaction.
讨论了焊缝是否存在压缩塑性变形问题和拉达伊d应力应变原理图存在的问题。
In this paper, the problems on compressive plastic deformation in the weld and the principle of welding stress and strain described by d.
采用平面应变有限元方法研究了晶须转动对晶须增强铝基复合材料热压缩变形行为的影响。
The effect of the whisker rotation on the hot compressive deformation behavior of the whisker reinforced aluminum matrix composite is investigated by the plane strain finite element method.
件是金属被施加压力，通过塑性变形塑造要求的形状或合适的压缩力的物件。
A piece is a metal that is applied to the object by means of a plastic deformation to shape the shape of the required shape or the appropriate compressive force.
有时直链较多的冷橡胶加入约1%的二乙烯基苯可轻微交联，从而改进可加工性和抗压缩永久变形性。
Sometimes the more linear cold rubbers are slightly crosslinked by the incorporation of about 1% divinyl benzene to improve processability and compression set resistance.
这样的方法会导致部件变形，被压缩，或直接破损。
It causes distortion, compaction, or breakage of components.
使共混胶料的耐油性、耐寒性、低压缩永久变形性能达到综合平衡，因此探讨了动态硫化工艺条件。
The dynamical vulcanization technique let properties of oil resistance, low temperature resistance and compression set of the blend turn into comprehensive equilibrium.
EPE压缩变形率，为同类包材中最低体积最小，适合多次撞击缓冲保护，精密仪器，电脑电子系列长途产品运输。
Epe compression and transformation rate are the lowest in same type of material. Suitable for repeatedly crash buffering. Long distance transport of precise equipment, electronic and computer.
EPE压缩变形率，为同类包材中最低体积最小，适合多次撞击缓冲保护，精密仪器，电脑电子系列长途产品运输。
Epe compression and transformation rate are the lowest in same type of material. Suitable for repeatedly crash buffering. Long distance transport of precise equipment, electronic and computer.
应用推荐