即在不发泡条件下，液体离子强度、表面张力对气液相混合不足以产生显著影响。
Without foaming, the mixing of liquids was not influenced evidently by ion strength and surface tension.
根据静态和动态气泡直径预测模型计算得到的结果可准确地用于预测不同发泡条件下闭孔泡沫铝胞直径。
The calculated results obtained with the static and dynamic models are capable of accurate predicting the bubble size under varied conditions of processing the closed cell aluminum foam.
通过实验对发泡聚苯乙烯热解回收苯乙烯单体的工艺流程提出了优化操作条件。
The optimum conditions for the technological process of recovering styrene monomer from foamed polystyrene were found.
实验确定了适宜的合成工艺及发泡工艺条件、产品性能。
Suitable technical conditions of synthesis and foaming, and properties of the product were determined experimentally.
在分析了影响合成过程、发泡剂发泡效率和泡沫稳定性因素的基础上，确定了上述两类发泡剂的最佳工艺合成条件。
The optimum condition for synthesizing the two type foaming agent was established based on the analysis of the factors which determine the synthesis process, foaming ability and the foam stability.
结果表明：在相同的条件下，MAB的增稠性能明显优于6501，发泡性能与6501相当。
The results demonstrated that, in the same condition, the thickening effect of mab is more obvious better than 6501, and the foamability is matchable.
研究特种发泡微胶囊的制备及其仿麂皮工艺条件。
The preparation of special foaming microcapsule and its application to suede like process were studied in the article.
用熔体发泡法制备了碳化硅颗粒增强泡沫铝样品，分析了碳化硅增强泡沫铝在准静态压缩条件下的变形行为。
SiC particle-reinforced aluminum foams were produced by melt foaming process, and their deforming activity under quasi-statistic pressing was analysised.
确定了在不同条件下铁水熔池熔融还原高炉粉尘发泡过程的曲线。
The foaming process curve under different conditions has been determined in iron bath during smelting reduction of blast furnace dust and sludge.
本课题主要研究了用一步法化学交联挤出发泡工艺成型PP发泡材料的原理、配方、工艺条件及其成型装置的组合与优化。
In the study, the theory, formula, technology and combination and optimization of apparatus for the crosslinked pp extruding foam in one-step were discussed.
分析讨论了试验工艺条件及工艺参数如混料条件、铝坯压缩条件和发泡中的加热温度、加热速度和保温时间对形成泡沫铝的影响。
The processing parameters, the effect of the mixing, the pressing parameter, the foaming temperature, heating rate and heat preservation time were studied.
研究了采用熔体发泡法制备的闭孔泡沫铝材料的轧制过程，分析了不同道次压下量条件下泡沫铝的变形特点与破坏方式，探讨了影响泡沫铝轧制能力的主要因素。
The rolling process of closed-cell aluminum foam that was prepared by melt-foaming process was studied, as well as its deformation and failure behavior due to different pass reduction.
在酸性条件下，这三种泡沫都几乎不发泡。
Meanwhile, the three kinds of foam cannot barbotage in the acid solution.
在酸性条件下，这三种泡沫都几乎不发泡。
Meanwhile, the three kinds of foam cannot barbotage in the acid solution.
应用推荐