介绍了轨道电路参数模拟装置的理论依据、方案和技术特征。
This paper introduces the basic theory, configuration and the technical characteristics of the parameter simulation device for trunk circuit.
结论：根据所有的参数模拟减压手术恢复关节的稳定性后，将交联试剂注射到腰椎间盘。
Conclusion. Injections of crosslinking reagents into lumbar intervertebral discs after simulated decompression surgery restored joint stability according to all parameters.
信息量用高计数和低计数模拟。空间分辨用改变滤波函数种类和滤波参数模拟，共模拟8种条件。
The simulation parameters include information dencity and spatial resolution. 8 filtering conditions were simulated by changing counts rate and filter parameters.
建立了二维轮胎橡胶材料的有限元模型，用应变能密度这个参数模拟了试样承受单向拉伸时裂纹的扩展方向。
A 2-d finite element model of tire-rubber was established to simulate the crack growth of the sample under simple tension, by using the strain energy density parameter.
方法：（1）模型建立：以相关的电学参数模拟血液动力学参数，以电路图（电路模型）分析的方法建立血液动力学理论模型。
Methods: (1)Model establishment: The hemodynamic model based on electrical circuit analysis was established by simulating hemodynamic parameters with electrical ones.
利用HSPICE电路模拟软件，对ESD保护结构进行了集总参数模拟，获得了保护结构在ESD事件中的功率和温度分布。
Both the power and temperature distributions of an ESD protection structure during an ESD event are obtained using HSPICE.
在岩石导电模型的基础上，参考双侧向仪器刻度电路原理，设计出适用于复电阻率测井仪器的刻度电路，并给出用电路参数模拟不同地层的方法。
Based on the rock conductivity model and with reference to calibration circuit in the dual laterolog tool, designed is calibration circuits in the complex resistivity logging tool.
在本文中，作者建立了翅片式蒸发器的分布参数模型，用以模拟结霜过程。
In this paper, the distributed parameter model of a finned evaporator is established to simulate the frosting process.
结果三弹性腔九元件集中参数模型模拟出的输入阻抗模和幅角与目标输入阻抗模和幅角能较好的吻合。
G. Fung et al. Results the modulus and phase simulated by the nine-element lumped parameter model could fit the goal input impedance well.
用幂函数模型描述的回归曲线以及根据试验参数得到模拟曲线与试验值比较误差均较小。
The errors are less as comparing the test data with regressive curve and simulative curve from test parameters using the power function model.
用幂函数模型描述的回归曲线以及根据试验参数得到模拟曲线与试验值比较误差均较小。
The errors of the data obtained using the power function model are very small from the test data.
最后采用指示模拟的方法建立了研究区的沉积微相模型，并以此模型为基础建立了研究区的储层参数模型。
The facies model and reservoir model of the study area were built up by using lots of indicators.
目前在风冷热泵机组的仿真研究中，对蒸发器结霜过程的模拟主要是采用一些由实验拟合而成的集总参数模型，而这些模型往往是在特定的运行条件下得到的。
At present, the lumped parameter model of frost, which is based on experience and depend heavenly on the running condition, is widely used in simulation of air-cooled heat pump.
本文采用一种集总参数模型模拟计算了地热系统的物理状态和参数。
On the basic data of obseved water level, the physical behaviour of the Hamar geothermal field was simulated using a Lumped parameter model.
采用贝叶斯指示条件模拟和序贯高斯模拟方法结合建立储层参数模型，很好地预测了储层非均质性展布。
With the combination of Bayes Indicator Conditional Simulation method and Sequential Gaussin Simulation method, the distribution of reservoir heterogeneity has been predicted.
采用选择的势函数模型以及矫正后的维里压力公式，对湿空气的PVT参数进行了模拟计算，并与相关实验数据进行了比较。
The PVT properties of moist air are calculated by chosen potential function model and modified virial pressure function, results agree well with experiment data.
采用选择的势函数模型以及矫正后的维里压力公式，对湿空气的PVT参数进行了模拟计算，并与相关实验数据进行了比较。
The PVT properties of moist air are calculated by chosen potential function model and modified virial pressure function, results agree well with experiment data.
应用推荐