将系统中的水排出，直到锅炉压力读数降为零。
Remon公司依靠一种传送能量的超声波制造芯片，使其传回压力读数。
Remon relies on a form of ultrasound that transmits energy to power the chip and prompt it to send back its pressure readings.
如果泄漏不超过25%，所有的量表压力读数都应该是相等的。
All gauge pressure indications should be equal, with no more than 25% leakage.
理论的运作：一火箭发动机推力对一个充满水的注射器，这产生的压力读数，就一连接压力计。
Theory Of Operation: a rocket engine thrusts against a water filled syringe. This produces pressure readings on a connected pressure gauge.
注：采用任何轮胎气压表也可以检查ET膨胀罐气体压力的准确读数。
NOTE: To get an accurate reading when checking et Tank air pressure with any tire gauge either.
这些提供了用于电气故障检修的模拟值的压力和驾驶性能分析所需的数据流读数。
These provide the electrical troubleshooting analogues of the pressure and flow readings needed for driveability analysis.
最好是使用相同的轮胎压力计和泵当您检查您的轮胎，因为你可能会取决于轮胎压力计，你选择不同的读数。
It is best to use the same tire pressure gauge and pump when you check your tires, because you may get different readings depending upon the tire pressure gauge that you choose.
用读数保持电路记录压力变化，较直接读取刻度值更加准确，可靠。
More precise and reliable recording is achieved by reading-keeping circuit compared with the original gauge-reading.
检查压力表读数。
总之，根据两杆枪压力表读数的情况，可以判断出管束是否泄漏和堵塞。
In short, according to the two gun pressure gauge readings, you can determine whether the leakage and blockage of the tube.
待位移传感器和土压力计读数稳定后，采用自上而下摘板的措施模拟桩前土开挖的施工过程。
In order to simulate the excavation process of soil in front of piles, the boards are taken down from top to bottom after the readings of displacement sensors and soil pressure cells are stable.
配置红色指针，可以“保持”在最高读数上，用于记录冲击压力或留着过夜以记录前一个晚上出现的最高冲击压力。
A red indicator hand that HOLDSat the highest reading registered, to record shock pressure or when left on overnight will register the highest surge pressure which occurred during that period.
配置红色指针，可以“保持”在最高读数上，用于记录冲击压力或留着过夜以记录前一个晚上出现的最高冲击压力。
A red indicator hand that "Holdsat the highest reading registered to record shock pressure. If left on overnight will register the highest surge pressure which occurred during that period."
如果量规（此处应该就是“压力表”）读数过高，将制动螺钉顺螺线方向放松； 如果量规读数过低，则向相反方向调整制动螺钉。
Loosen the clamp screw(s) and move slightly toward the helix if gage is reading high. and away if reading low.
如果量规（此处应该就是“压力表”）读数过高，将制动螺钉顺螺线方向放松； 如果量规读数过低，则向相反方向调整制动螺钉。
Loosen the clamp screw(s) and move slightly toward the helix if gage is reading high. and away if reading low.
应用推荐