在一般条件下，标准齿轮滚刀只能加工与其模数、压力角相同的同制齿轮。
Generally, standard gear hobs are only used to machine gears with the same modul, pressure Angle as hobs themselves.
本文提出用标准齿轮滚刀加工与其模数、压力角不同的异制齿轮的方法，并给出了相应的验算方法。
In this paper, a method of employing standard hobs to machine gears with different module and pressure Angle is presented. The relevant checking calculation method is also put forward.
同时，为了实现系统测量快速性的需要，选用流水线型模数转换器ads800进行压力模拟信号的数字化转换。
At the same time, in order to meet the need of fast measurement, pipeline analog-to-digital converter ADS800 is selected to convert analog signal of pressure.
讨论了无因次渗透率模数和表皮系数对压力响应的影响。
The influences of dimensionless permeability modulus and skin factor on pressure response are discussed.
细高齿齿轮是采用小模数、小压力角、大齿顶高来加大端面重合度，达到提高齿轮强度、降低噪声的目的。
High tooth gear has small module, small pressure Angle, and large addendum to enlarge the transverse contact ratio, improve gear strength, and reduce the noise.
本文阐述了渐开线直齿圆柱齿轮顶圆直径及齿轮模数、变位系数和压力角等参数的确定方法和步骤。
The method and procedure of measuring and calculating involute spur gear geometrical parameters such as tip diameter, module, modification coefficient and pressure Angle were shown in this paper.
在用遗传方法对灰色理论建模数据进行全局优化的基础上，建立了预测冻结法施工中外层井壁承受冻结压力发展趋势的智能灰色理论模型。
On the basis of the global optimization of data which is used to build up mold, the artificial intelligent grey theory mold was established to forecast the freeze pressure development trend.
该校验仪通过步进电机对密度继电器压力进行调节，并通过模数转换电路采集压力传感器的输出，实现对密度继电器报警及闭锁压力的测量。
It can control the stepper motor to change the pressure of the relay, and the A/D circuit samples the signal of the pressure sensor and then acquires the lock or alarm value after processing.
讨论了溶洞和裂缝无因次渗透率模数、介质间窜流、弹性储容比、外边界条件及表皮系数对压力响应的影响。
Effects of permeability modulus, interporosity flow parameter, storativity-ratio, outer-boundary and skin parameter to the pressure response are discussed.
本文详细介绍了用于齿轮仪器校准的齿轮样板模数、压力角、螺旋角等参数计算方法。
The way of calculating the parameters of modulus, pressure angle and helix angle of the gear masters that are used to calibrate gear instruments is in detail in this paper.
介绍一种用模数转换器(adc)进行温度补偿的压力测量电路，对模数转换器(adc)在温度补偿中的原理和作用进行了论述和分析。
A kind of pressure measuring circuit with ADC for temperature compensation was introduced. The principles and functions of ADC circuit in temperature compensation were discussed in detail.
分别分析了基蜗杆半径、插齿刀模数、齿数、压力角对基蜗杆曲面奇异点位置的影响。
The influence of the base worm radius, the module of shaper, the teeth number and the pressure Angle on the singularity point were analyzed, respectively.
中间平面内蜗杆与蜗轮的模数和压力角分别相等，即蜗轮的端面模数等于蜗杆的轴面模数且为标准值；
The worm and worm among plane within the modulus and pressure Angle, namely the worm gear were equivalent modulus is equal to the end of the worm shaft side modulus and for standard;
中间平面内蜗杆与蜗轮的模数和压力角分别相等，即蜗轮的端面模数等于蜗杆的轴面模数且为标准值；
The worm and worm among plane within the modulus and pressure Angle, namely the worm gear were equivalent modulus is equal to the end of the worm shaft side modulus and for standard;
应用推荐