对这些织物的压缩性能进行了测试，分析了压力—变形曲线和影响压缩变形和回复性能的因素。
Also, the compressive properties of the fabrics were measured, and the pressure-deformation curve and some factors influencing the compressive deformation and recoverability were analyzed.
实验所得的加压精度与理论分析结果比较接近，加压装置的压力与变形之间基本呈线性关系。
Requirements and the accuracy of pressure element were analyzed in theory, and the experimental results tallies basically with it.
研究了用反分析理论和内、外边界元方法预测软岩巷道围岩压力和支护变形。
Study on applying the theory of inverse analysis and in-out boundary element method to forecast the pressure of soft rock tunnel 'surrounding rock and supporting deformation.
通过计算分析可以发现：随着土的变形模量和泊松比的减小，由地震所引起的海床中的累积超孔隙水压力均增大。
By computations and analysis it is found that the seismic-induced accumulative pore water pressures of seabed increase with the values of soil deformation modulus and Passion's ratio decreasing.
实例分析了不同土性参数情况下有限变形和小变形理论在压力场、位移场和应力场等方面的差异。
The differences between finite deformation and small deformation in such aspects as pressure field, displacement field and stress field are analyzed with different soil parameters.
先期固结压力是土的重要力学特性参数，对变形计算和强度分析有较大影响。
The preconsolidation pressure is an important parameter for soil deformation calculation and strength analysis.
通过对常用支撑结构的力学分析与性能对比，选用简支梁作为压力传感器敏感变形机构。
After analyzing and comparing the performance of normal bracing structures in mechanics, we use a freely supported beam for sensing deforming structure.
在此基础上，阐述了液压冲孔的变形机理，分析了液体压力对冲孔质量产生的影响。
The deformation mechanism of hydropiercing was concluded based on the calculation results. Influence of liquid internal pressure on hole quality was investigated.
并对强旋过程中各阶段的变形情况和旋压力的变化进行了分析。
The distortion and changing of spinning force in variable stage is analyzed also.
最后对三种结构型式的拱顶储罐的变形方式、应力状态、塑性变形历史、塑性极限压力、弹性失稳临界压力进行了分析与对比。
The analysis and contrast of deformation pattern, state of stress, plastic deformation history, plastic limit load and limit load of elastic buckling are analyzed and contrasted.
以粘弹性薄板为模型，应用材料流变学理论及弹性薄板理论，分析计算了连铸板坯在钢水静压力与不均匀温度场作用下所发生的鼓肚变形与应力。
Based on the viscoelastic plate model, rheology theory and elastic thin plate theory, the bulging deformation and stress in continuous cast slabs were analyzed and calculated.
通过改变储层渗透率和初始地层压力，分析了储层变形对煤岩气藏单井产能的影响。
By changing the initial formation of reservoir permeability and pressure, the impact of coalbed gas single well productivity was obtain.
本文将反应堆压力壳的球顶盖、上下法兰、螺栓、筒体及双道O形环作为一个超静定系统进行了应力和变形分析。
The reactor pressure vessel composed of spherical top and lower heads, upper and lower flanges, bolts, cylinder and two O-rings, as a static indeterminate system has been studied.
介绍并分析了在研究筒体应力和变形中几种轮带对筒体压力分布的假定。
Several assumptions of the shell's stress distribution are introduced and analysed, a formula is derived for the stress distribution in the paper.
对影响薄壳塑件翘曲变形的因素（如模具温度、熔体温度、注射速率、保压压力等）进行分析，提出翘曲产生的原因及相应的改进措施。
The factors that affect thin-wall mould warpage, such as mould temperature, melt temperature, rate of injection and holding pressure, etc, are analyzed, in addition the ca…
对轧制过程中轧制压力分布进行了分析，得到其分布规律为轧制压力在变形区中间区达到最大值，而在入口和出口处逐渐减少。
The rolling force distribution was analyzed to obtain its character which reaches the maximum value in the centre of the rolling zone, while at the entrance and exit, the stress fades away.
本文分析了九个工程的岩体现场变形试验资料，把变形试验中可能出现的压力—变形曲线概括为五种基本类型。
This paper dealt with the in-situ test results on the deformability of rock masses in nine hydroelectric projects.
利用有限元软件ANSYS对重轨的压力矫直过程进行了三堆有限元模拟，对重轨矫直过程中的弹塑性变形过程进行了分析。
The press straightening process of heavy rail was simulated and researched by finite element software of ANSYS.
模流分析、温度分析、填充分析、压力分析、翘曲变形分析、结构评审（初审、定型评审、终审）、分型线结构评审、定模结构评审、动模结构评审、水路分布评审。
Mold Flow Analysis, Temperature Analysis, Fill Analysis, Pressure Analysis, Buckling Deformation Analysis, Structure Review, Parting Line, Fixed Mold, Moving Mold, Water Circuit.
模流分析、温度分析、填充分析、压力分析、翘曲变形分析、结构评审（初审、定型评审、终审）、分型线结构评审、定模结构评审、动模结构评审、水路分布评审。
Mold Flow Analysis, Temperature Analysis, Fill Analysis, Pressure Analysis, Buckling Deformation Analysis, Structure Review, Parting Line, Fixed Mold, Moving Mold, Water Circuit.
应用推荐