本文针对无卡轴旋切机振动刀架机电式振动装置的缺点，设计了一种液压振动系统。
This paper describes a hydraulic vibrating system. This system is in accordance with the shortcomings of the mechanical vibration installation that cuts with the use of a vibrating machine tool.
介绍我国市场上小径木无卡轴旋切机的旋切原理和改进后小径木无卡轴旋切机的旋切原理。
Briefed the principle of the small-diameter spindleless veneer lathes in the domestic market and discussed the principle for the improved model.
本论文通过对无卡轴旋切机原理和旋切曲线的研究，推导出了变速进给系统的数学模型，以保证所旋切的单板厚度均匀。
Based on the study of the lathe principle and peeling curve the thesis developed mathematical model of variable-speed feeding system to guarantee the even veneer thickness.
而且，季风槽向南移动轴的今天经过比卡内尔，迪萨，贾巴尔普尔，赖布尔，低压区中心。
And, the southward moved axis of monsoon trough today passes through Bikaner, Deesa, Jabalpur, Raipur, Center of low pressure area.
介绍了一种基于PC机的IS A总线步进电机控制卡，实现多轴联动控制，讨论了其工作原理和硬件结构设计、软件设计。
One kind of stepping motor control card based on ISA bus of PC which achieved multi-spindle linkage control is introduced, its principle and design of hardware construction and software are discussed.
齿轮零件组安装非常容易，可以搭配传动轴完成工作卡上的图案。
It is to complete the colourful pictures on the inserted working card.
该运动控制卡能同时采集四轴的编码器脉冲信号，输出四路模拟电压控制伺服电机，同时能控制I/O信号的输入和输出。
The card can collect four axes' encoder pulse signals simultaneously, and control servo motor by four output analog voltage. Furthermore, it can control input and output I/O signals.
并以基于PC和运动控制卡的开放式四轴数控系统实现支管端头的变角度焊接坡口面切割。
The open four-axis CNC system based on PC and motion control card can accomplish the cutting of various-angle welding plate.
过载、超温或轴卡滞情况发生会停止电极的工作并且会由显示指示器和声响警告器给出信号。
Overload, over-temperature, or shaft jam conditions stop the motor and are signaled by a display indicator and audible alarm.
文章采用PCL-839三轴步进电机控制卡开发了一套基于DOS的专用数控系统，并对该控制卡功能的扩展进行了分析。
The article exploits a special NC system based on DOS, choosing PCL-839 3-axis stepping motor control card, and analyzes the expansibility of the card.
该清管器的钢轴能在较大推力作用下发生弯曲变形，有利于通过弯头或变形管段，可有效避免堵卡事故的发生。
The steel axle of this kind of pig can bend under greater thrust force, it is helpful to pass through elbow or the section of converting pipe, so it can avoid efficiently block accident.
文章介绍了一种采用PCI专用接口芯片pci9052作为PCI总线与DSP (TMS320 LF 2407)的接口桥接器，实现6轴运动控制卡的硬件设计方法。
In this article, to carry the 6-axis motion controller out, a method of using PCI special interface chip PCI9052 to be a interface bridge of PCI bus and DSP (TMS320LF2407), was introduced.
叙述了地毯簇绒机中横动运动的伺服控制，提出了基于可编程多轴控制器（PMAC）运动控制卡的半闭环控制系统。
Principle of thwartwise motion in tufting machine, hardware and function of Programmable Multi-Axis Controller (PMAC) and controlling process were presented.
在这个运动控制的核心就是一块3轴伺服运动控制卡。
The core of the motion system is 3 -axis-servo-motion controller.
简单介绍了双轴运动平台实验系统以及其中的控制器PM AC卡和如何在PM AC中实现用户自定义的控制算法。
The paper introduces the dual-axes platform system, the PMAC and the PMAC's development software. It also introduces how to realize the user own algorithms.
修正：解决一个问题，造成“小缺口”发现“链接”选项卡下，变灰，无法在5轴模块。
Fix: Resolved an issue in the 5-axis module that caused the "Small gaps" found under the Link TAB, to be grayed out and unavailable.
本文介绍了多轴位置控制卡的结构及原理，并详细介绍了VHDL语言在多轴位置控制卡电路设计中的应用。
In this paper, the construction and principle of multi-axis position control module are introduced. At the same time the application of VHDL to carry out the work is discussed in detail.
所述中间导轨放置在所述两块竖直放置的板中间，两块板上的四个支撑轴分别放入所述中间导轨的四个卡槽中。
The intermediate guide rail is set between these two perpendicular boards, the four support shafts on these two boards are set separately inside the four slots.
电器控制系统采用美国PMAC四轴控制卡及人机界面，稳定性强，同时实现了对整机进行实时监控，实现了快速调整和操作。
Electricity control system adopts PMAC from U. S. a and man-machine interface. It realizes high stable performance, real-time detection of whole machine, prompt adjustment and operation.
叙述了2.16米天文望远镜卡焦及折轴光学系统的调整原理与具体步骤。
In this paper, the principle and procedure of alignment of Cassegrain and coude optical systems for 2.16m astronomical telescope are described.
无法兰轴类校中装置，包括测量臂、卡套、安装螺钉及百分表。
The checking center device without the flange axis includes the measure arm, the cutting sleeve, the installment bolt and the dial indicator.
本设计目的是完成195柴油机摇臂轴座的模具设计，摇臂轴座加工工艺路线及工艺卡的制定，部分工序专用夹具的设计等。
The design aims to complete the module design of 195diesel rocker axle base, the draw up of its processing line and procedure card and the design of manufacturing special fixture, etc.
牵引卡的销轴不会自行窜出，降低了事故的发生。
The accident occurring rate is decreased because the pin bearing of the dragger is prevented escaping automatically.
牵引卡的销轴不会自行窜出，降低了事故的发生。
The accident occurring rate is decreased because the pin bearing of the dragger is prevented escaping automatically.
应用推荐