单向拉伸镍钛合金带中从奥氏体到马氏体的相变已在实验中观测到，并被看作为局部变形进行了数值模拟。
Phase transformation from austenite to martensite in NiTi alloy strips under uniaxial tension has been observed in experiments and has been numerically simulated as a localized deformation.
本文对该体系的节点进行了单向拉伸情况下的应变变化情况及其整体变形、节点连接破坏情况性质的分析。
This paper analyses the load-deformation and the whole deformation of the system joint when it is in the single direction drag and the destructive quality of joint connection.
本文利用微观力学方法研究了单向连续纤维增强的金属基复合材料的弹塑性变形行为。
A micromechanical method is used to study the elastoplastic behavior of metal-matrix composite reinforced by unidirectional fibers.
利用正应力图形和剪应力图形，分析了单向拉伸、拉深及挤压工序中典型点的变形类型及尺寸变化趋势。
In addition, the stress-strain of typical points in simple tension, drawing, and extrusion was successfully analyzed by the figures.
本文研究了含中心微孔的超弹性矩形板在单向拉伸时的有限变形和受力分析。
In the present paper, the finite deformation and stress analysis for a hyperelastic rectangular plate with a center void under a uniaxial extension is studied.
特别针对砂性土壤，提出了应用室内三轴循环试验的结果评估单桩在单向循环侧向力下的变形方法。
The usually used design method, p-y curves method, is unsuitable for estimating the deformation response of the large-diameter monopile under long-term cyclic lateral load.
由有限变形理论推导出单向压缩和平面应变有限元模型。
The corresponding constitutive equations based on finite deformation theory are presented.
该文以铅作为试验材料，测定单向压缩有限变形和双向受约束两种情形下的载荷位移曲线，建立了基于欧拉描述的铅有限变形本构方程。
The keypoint to simulate the metal forming process by using finite deformation theory is to define the constitutive equations of the material.
利用背散射电子衍射取向成像技术定量分析了热模拟单向压缩条件下Q235碳素钢热变形时铁素体的织构形成规律。
The textural features during ferrite refinement by deformation enhanced transformation were analyzed by means of orientation mapping based on the EBSD technique in a Q235 low carbon steel.
利用背散射电子衍射取向成像技术定量分析了热模拟单向压缩条件下Q235碳素钢热变形时铁素体的织构形成规律。
The texture evolution of ferrite during warm compression of Q235 low carbon steel was determined quantitatively by means of orientation mapping based on the EBSD technique.
采用结构代表胞元模型数值模拟了在不同相对密度范围的单型铝蜂窝结构在单向压缩过 程中的变形、失稳和破坏现象。
The model of representative unit cell (RUC) is used to numerically simulate the deformation, instability and collapse of single-mode aluminum honeycombs under uniaxial compression.
结果表明，微裂缝性特低渗透油藏一维单向渗流的压力分布影响因素比较多，如启动压力梯度、变形系数、生产压差和排距等，并且这些因素均以非线性方式产生综合影响。
The single-phase porous flow plugged by mobile gels is nonlinear, the starting pressure of oil is lower than that of water, and the permeability of oil is higher than that of water.
结果表明，微裂缝性特低渗透油藏一维单向渗流的压力分布影响因素比较多，如启动压力梯度、变形系数、生产压差和排距等，并且这些因素均以非线性方式产生综合影响。
The single-phase porous flow plugged by mobile gels is nonlinear, the starting pressure of oil is lower than that of water, and the permeability of oil is higher than that of water.
应用推荐