在对移动机构的静态和动态进行受力分析的基础上，确定了单个磁性吸附块的最小吸力参数。
On the basis of the static and dynamic stress analysis about the traveling mechanism, the minimum suction parameter of the single magnetic adsorbing block was determined.
通过对错流过滤系统中悬浮颗粒的受力分析，建立动态膜涂膜过程数学模型，可计算整个过程中的膜通量和膜厚度。
A simple model of dynamic membrane forming in crossflow filtration is presented which can predict filtrate flux and dynamic membrane thickness through the analysis of force on the particles.
针对TBM施工隧道仰拱预制块的特殊结构，采用围岩-结构模式，进行了模拟施工动态的受力影响计算分析。
According to the special structure of precast block of inverted arch for TBM construction tunnel, the dynamic construction state is modeled by FEM with surrounding rock - structure calculating model.
本文从静态和动态二方面对系统进行受力分析和计算。
In this paper, we can go in on the force analysis and calculation in both static and dynamic phases.
利用UG软件对运煤车进行实体建模，在AD AMS软件中对运煤车进行动态仿真，对其起动转矩和几个关键部分的受力进行了分析。
This paper built the solid model of a coal car with UG software, made dynamic simulation by ADAMS, and measured the starting torque and the forces on several key parts of the coal car.
为了降低阻尼系数进一步提高泵的动态性能，通过对JBP-63型径向柱塞变量泵定子受力仿真分析，研究了减小径向柱塞液压泵的定子不平衡力的方法。
Aimed to decrease damping coefficient and enhance pump's dynamic performance, a method for reducing the radial plunger pump stator forces was developed by analyzing the type JBP-63 pump stator forces.
本研究从固定式三油楔动压滑动轴承动态工作状况分析入手，分析了固定三油楔动压滑动轴承的原理以及变载荷工况下的受力状态；
The thesis come from the analysis of stationary type tri-oil wedge dynamic-pressure sliding bearing dynamic working condition, analyse its elements and stress in variable-load operating mode.
通过对三环减速机环板动态受力过程的分析与振动试验，揭示了其振动发生根源。
The vibration generating mechanism of a new type of mechanical transmission unit have been analyzed and revealed through theoretical analysis and vibration measurement on a test-rig.
在进行挖沟器的系统动力学分析过程中，利用了虚拟样机技术adams软件对挖沟器链传动过程中的受力情况进行了动态仿真。
During the dynamic analysis of mechanical system, the force that act on the chain of trenching implement is simulated by virtual prototype soft ADAMS.
利用SD 375动态分析仪和SAS3.0分析软件包测取气缸盖的动态特性和模拟实际受力时的受迫变形。
With the help of SD375 dynamic analysis system and SAS3.0 analysis programs, the dynamic properties and forced deformation of cylinder head are investigated.
然后对主切机构进行了动态静力学分析，得出一个运动周期中各铰接点的受力情况。
Then the analysis of dynamic statics about mould-cut main mechanism is given and the analysis about force of each joint point in a motion period is put forward.
简要介绍了电磁动态单螺杆挤出机的结构性能，分析了螺杆在振动力场作用下的轴向受力状况。
The structure and the performance of the single screw extruder of electromagnetism dynamic are presented. The axial force distribution on the screw under the vibration force field is analyzed.
简要介绍了电磁动态单螺杆挤出机的结构性能，分析了螺杆在振动力场作用下的轴向受力状况。
The structure and the performance of the single screw extruder of electromagnetism dynamic are presented. The axial force distribution on the screw under the vibration force field is analyzed.
应用推荐