本控制系统由交互式绘图编程、加工控制、大功率脉冲电源三部分组成，主机采用奔腾586计算机。
This system consists of interactive-drawing programming system, control of working, power source with large power pulse, the main unit uses pentium 586 chip.
在电热、电磁发射技术中，高功率脉冲电源占据着非常重要的位置，开关是高功率脉冲电源的重要组成部分。
In the electrothermal chemical and electromagnetic launch technology, the high power pulsed sources occupy a very important place.
采用爆炸冲击波作用于贮存有电极化能量的铁电体，迫使其转变成反铁电体，可释放出巨大电能量，用于一次性的高压、大功率脉冲电源。
A ferroelectrics could release total electric polarization energy during it is transformed to antiferroelectrics, and that was used to high electrical power supply.
分析了正弦激励下的RLC电路作为脉冲功率电源的可能性。
Under sinusoidal excitation, the feasibility of utilizing RLC circuit as the impulse power source is analyzed.
脉冲功率电源稳定工作的极限频率取决于间隙绝缘强度的恢复时间。
The limit frequency of the stable action of the pulsed power source depended on the reinstated time of the gap insulation.
实验结果表明，这种高频脉冲电源在高频、窄脉宽、大功率等方面均能满足该工艺的要求。
The result has dedicated that it could satisfy the process of PECM in high frequency, narrow pulse width and high-power.
提出采用大功率IGBT设计变极性脉冲MIG焊双逆变弧焊电源。
The high-power IGBTs are adopted to design the dual inverter arc-welding power source for variable polarity pulse MIG welding.
该放电回路适合rsd的测试及其脉冲功率电源。
This circuit is suitable for RSD test and pulsed power supply with RSD.
大功率TEACO2激光器系统产生的强电磁干扰主要来源于激光器主放电回路、脉冲火花开关和电源。
The strong electromagnetic interference generated in high power TEA CO2 laser system mainly comes from the main discharge circuit, pulse spark switch and power supply.
介绍一种高功率脉冲二极管激光电源。
This paper introduces a new high power Q - CW pulsed laser diode driver.
所研制的小能量脉冲功率电源体积小、成本低、操作方便且运行可靠。
The pulsed power source is developed on the principles of small size, low cost, convenient operation and high performance reliability.
PEF非热食品处理的关键技术之一是设计、制造大功率高精度的高压脉冲电源。
Designing and building high precise, high voltage pulse generator is expected to be the key technologies for PEF to cold pasteurize liquid food.
根据脉冲mag焊工艺特点，脉冲焊电源必须具有良好的动态特性、较大功率输出以及较高的可靠性。
According to the technological trait of pulse MAG welding, the pulse welding power source has been requested to have better dynamic character, biggish output power and upper reliability.
通过对脉冲功率电源电路参数和电磁炮参数的分析，建立了两者之间的关系方程并对电源电路进行了设计。
Analyzing the circuit parameters of pulse power source and the parameters of EM gun, an equation concerning the two kinds of parameters was obtained and the source circuit was designed.
指出大功率脉冲叠加电源是铝及铝表面硬质处理的首选电源。
It was shown that high power pulse superposition current supply was the optimum choice for hard surface treatment of al and al alloys.
该仪器由可编程脉冲发生器、高压可调稳压电源、高压功率开关和保护电路组成。
It mainly consists of a programmable pulse generator, adjustable high voltage regulator, high voltage switch and protection circuits.
但由于达到神经电位阈值所需的磁刺激脉冲能量较大，对电源功耗的要求限制了磁刺激的高频应用，本文研制了一种用于高频磁刺激仪的双向充电电路，用以降低功率消耗。
The objective of this paper is to present a novel design of the bidirectional charging circuit used in the high frequency magnetic stimulator to lower the electric power consumption.
实际结果表明，我们研制的脉冲激励电源可以满足大功率TEACO2激光器的特殊工作要求。
The experimental results demonstrate that this pulsed exciting power supply developed by our lab can totally satisfy the special requirement of the high-power TEA CO2 laser.
本文从提高超声电源峰值功率出发，分析研究了脉冲驱动及脉冲电流两种不同的脉冲形式，同时研究了这两类产生脉冲的电路。
Pulse drive and pulse current were studied in this paper aim at improving peak output power of the ultrasonic generator. At the same time these two types circuit for producing pulses were studied.
大功率TEACO2激光系统工作时产生的强电磁干扰主要来源于激光主放电回路、脉冲火花开关和电源。
The strong electromagnetic interference generated in the operation of the high-power TEA CO2 laser system mainly comes from the main discharge loop, pulse spark switch and power supply module.
大功率TEACO2激光系统工作时产生的强电磁干扰主要来源于激光主放电回路、脉冲火花开关和电源。
The strong electromagnetic interference generated in the operation of the high-power TEA CO2 laser system mainly comes from the main discharge loop, pulse spark switch and power supply module.
应用推荐