同时进行了冷藏鸡蛋的抗压力学性能试验研究。
Meanwhile the study on the compressive mechanical characteristic of the refrigerated egg was conducted.
分析、例举了预应力钢材力学性能试验中常见的误差！
The paper listed the common error in mechanical property test of PC steel products.
介绍了金属材料试样制备与力学性能试验结果的相关性。
The relativity for preparation of specimens and results of mechanical testing for metallic materials was introduced in a systematic way.
对铅黄铜作了深冷处理，并进行力学性能试验和金相组织分析。
The Pb brass has been treated with cryogenic treatment, the mechanical properties testing and microstructure analysis have been done.
新的力学性能试验标准必须包含测量不确定度阐述的技术内容。
The new standards must contain the content describing uncertainty in measurements.
介绍了可编程控制器在转椅力学性能试验机的气-电控制系统中的应用。
This paper described the PLC application in the pneumatic-electrical control of the test of swivel chair mechanical property.
介绍了俄罗斯铁路货车18- 578型转向架的改进及线路动力学性能试验。
Described are the improvement and dynamics performance on-track test on 18-578 bogies for Russian railway freight cars.
结果表明金属材料试验试样的制备与力学性能试验的结果有着非常密切的相关性。
The results showed that specimen preparation has close relationship with the results of mechanical testing for metallic materials.
对488发动机气缸盖使用的MS6876铝合金进行了系列温度下的力学性能试验研究。
The experimental investigation of mechanical properties for MS6876 aluminium alloy used for making 488 engine cylinder heads under a series of temperatures is Carried out.
分3个阶段10种荷载工况进行模型的力学性能试验，研究简支下承式钢桁结合梁桥的受力性能。
The mechanical property test of the model covering 3 stages under 10 load conditions is carried out to study the loading property of through truss composite beam with simple support.
针对百色工程碾压混凝土局部出现的弹簧现象，进行了简单的原因分析，并对此进行了力学性能试验研。
For the local spring phenomenon occurred in RCC of Baise multipurpose dam project, the author makes an elementary analysis on the cause, test and study the mechanical property correspondingly.
用TEM、电阻、力学性能试验等方法研究了固溶后的冷变形对6082铝合金时效析出过程的影响。
The effect of cold deformation on the aging precipitation of the solution-treated 6082 Al-Mg-Si alloy was investigated by the methods of TEM, electric resistance, mechanical properties tests.
通过充填聚氨酯泡沫的薄壁金属圆筒的力学性能试验，研究薄壁金属圆筒内充填聚氨酯泡沫的作用和效果。
Based on the mechanical property test on the thin wall metal cylinder filled with polyurethane foam, the effects of polyurethane foam filling in the wall metal cylinder are studied.
介绍了现在通行的燃料棒辐照后破坏性检验的一般方法，包括燃料辐照后的微观结构观察和力学性能试验；
Several methods of destructive post-irradiation examination(PIE) including microstructure observing and measurement of mechanical properties of irradiated fuel rod were introduced.
通过硅橡胶力学性能试验，得出用硅橡胶的拉伸、撕裂、剥离强度等性能指标，可以满足气囊模具的要求。
Tested the mechanical properties of silicon rubber, tensile, tearing and peeing strength can are meet the demand of inflatable bag.
阐述了一些典型的试验分析与研究成果，包括橡胶隔震支座力学性能试验与隔震房屋振动台模型试验的成果；
Some typical testing analysis and researches, including the mechanical tests for rubber bearings and the shaking table tests for structural models with isolation system were provided herein.
力学性能试验结果表明，电磁搅拌作用下，AZ31镁合金的布氏硬度、抗拉强度明显提高，但伸长率变化不大。
Mechanical performance test result shows that the effect of electromagnetic stirring can significantly increase the hardness and mechanical properties of AZ31 alloy, but elongation change little.
从混凝土磨蚀和力学性能试验得知，水工混凝土的磨蚀程度依赖于混凝土的初始磨损率，抗拉强度和极限拉伸变形值。
Abrasion and mechanical properties test of concrete have shown that the degree of abrasion dependent on initial abrasion ratio, flexural strength and limit strain.
通过渗氢试样的常温力学性能试验和双悬臂梁试样在高温高压高纯水中的腐蚀试验来研究t 225ng钛合金的氢脆行为。
Through the tests of mechanical properties of charging hydrogen and the corrosion tests in loop water of high temperature and high pressure, hydrogen brittleness of T225NG Ti-alloy was studied.
通过金相技术、力学性能试验和SEM技术研究了6061-T6铝合金真空电子束焊接接头的金相组织、力学性能和断口形貌特征。
The metallurgical structures, mechanical properties and fractographs of EB welded 6061-T6 aluminum alloy joint were studied by means of metallography, mechanical test and SEM technology.
采用化学分析、力学性能试验和金相检验等方法对该裂纹进行了分析。结果表明，此缺陷是由于试验环原始表面的粗糙度过大造成的。
By means of chemical composition analysis, mechanical property test and microstructure examination, the results showed that this defect was result of rough surface and not the crack existed in matrix.
通过高温瞬时试验、剥落腐蚀试验、扫描电镜及力学性能试验，对经均匀化和不经均匀化的5083铝合金铸锭的轧制制品进行对比分析。
The rolling products by homogenizing ingot and non-homogenizing ingot are analysed and compared through high temperature property tests, corrosion tests, SEM analysis and machine property tests.
文章分析了自保护药芯焊丝的主要成分及作用，介绍了天津市金桥焊材集团有限公司研制的X80管道钢用自保护药芯焊丝的力学性能试验结果。
The influence of pre-heating temperature on organization and performance of X80 pipeline steel was investigated by weld thermal simulation technique and the instrumented Charpy impact toughness test.
文章通过对具有代表性的二灰砂砾不同龄期的力学性能试验分析研究，提出了用7天强度和7-180天强度增长率作为二灰砂砾力学性能的评价指标。
Through representative lime-flysch gravel mechanics capability test and analysis, put forward 7days antipress intension and 7-180 days intension rising rate and make them as lime-flysch gravel index.
力学性能试验结果表明，不加填充材料焊接时，试样拉伸强度仅为母材强度的31.24%；进行原位焊接时，试样强度达到母材强度的50.89%。
The mechanical testing results showed that tensile strengths of samples welded by direct welding is only 31.24% of that of the parent metal, and 50.89% of that by "in-situ" welding.
通过凝胶含量测定、力学性能试验以及熔体流动性能测试等手段，研究了共混（反应）时间对密炼法和挤出法反应性PP/EPDM共混合金性能的影响及其机理。
The effect of blending time on the properties of reactive PP/EPDM alloy was studied via the analysis of gel content, mechanical properties, melt flow behaviour and morphology.
采用理论与试验相结合的方法研究了这类材料的力学性能与主要失效方式。
The mechanical properties and failure patterns of the clad material are investigated with the method of experiment and theory.
试验结果表明，添加聚丙烯纤维有助于改善材料的模压性能，但导致材料物理力学性能下降。
The test results showed that adding virgin PP fiber could improve molding performance of the composite, but made the physical mechanical properties reduced.
AAI公司的一位代表说，这次初始飞行试验达到或超过了所有的预期试验目标，证明了这种新型机身具有良好的空气动力学性能。
This initial flight met or exceeded all test objectives and validated the aerodynamic capabilities of the new airframe, according to a company representative.
AAI公司的一位代表说，这次初始飞行试验达到或超过了所有的预期试验目标，证明了这种新型机身具有良好的空气动力学性能。
This initial flight met or exceeded all test objectives and validated the aerodynamic capabilities of the new airframe, according to a company representative.
应用推荐