对于同样外形的材料，刚度与弹性模量是成比例的。
For identical shapes, the stiffness is proportional to the modulus of elasticity.
织物硬挺度测试仪，可通过简单操作及计算测出织物的弯曲高度、弯曲刚度、弯曲模量。
Fabric Stiffness Tester. To determine the bending height, flexural rigidity and bending modulus of fabric by simple procedures and calculation.
一个结构的刚度将受到弹性模量和面板厚度的影响。
The stiffness of a structure will be subject to elastic modulus and panel thickness.
由该公式确定的碰撞刚度不但与转子和定子的杨氏模量有关，而且与转子的径向速度有关。
The colliding stiffness by this formula is not only concerned with Young's modulus of rotor and stator, but also concerned with the radial speed of rotor.
目的：研究不同刚度的股骨头假体置换后的生物力学影响及材料的弹性模量与力学相容性关系。
Objective: To study biomechanical influence and relations between the elastic modulus and mechanical compatibility for prosthesis of different stiffness after replacement.
一个结构的刚度将受到弹性模量和面板厚度的影响。
The stiffness of a structure will be the elastic modulus and the effects of panel thickness.
抗弯刚度的概念是材料切线模量和截面对中和轴的惯性矩的乘积。
The bending stiffness of elastoplastic member is product of tangent elastic modulus of material and inertia moment of the section.
高性能混凝土具有高强度、刚度、弹性模量和耐久性。
The concrete with high properties has the characteristic of high strength, stiffness, elastic modulus and durability.
导出了钢管混凝土柱弹性本构方程、组合轴压弹性模量和组合轴压刚度的理论计算公式。
The elastic constitutive equations, the composite elastic modulus and the composite axial compression stiffness of CFST are derived.
分析了复合材料面层的弹性常数、泡沫芯层的模量和夹层结构的刚度；
The elastic modulus of foam core and composite skins and the stiffness of sandwich are analyzed.
基体的强度和弹性模量从零开始增加，到一定龄期后接近集料分散相，对于轻集料混凝土，基体的强度和刚度在一定龄期还将超过集料分散相。
The strength and modulus of elasticity of matrix increase from almost zero, then at a certain age up to those of the coarse aggregate, and even exceed for lightweight concrete.
本文介绍高速输送带弹性振动的基本公式，阐述我国目前常用几种输送带的圆柱刚度和杨氏弹性模量等振动系数的计算法。
This paper introduces basic formulas of elastic vibration of conveyor belt and the calculation of its vibration coefficients e. g. cylindrical rigidity and modulus of elasticity.
采用等刚度法确定换填基础模量；
The replacement foundation modulus was ensured by the method of equivalent-stiffness.
该弹簧单元与磁流变液屈服前区的初始剪切模量和蓄能器的刚度等有关。
The spring element stiffness is related to pre yield shear modulus of MR fluid and accumulator stiffness.
提出了“刚度相似”的方法，有效地解决了模型与实型各部分结构弹性模量相似比不一致的模型设计问题。
It presents the method of "stiffness similarity", which has solved the design problem of model with difference of elastic modulus ratio in different parts between model and practicality.
汽车内部件。10% 玻璃纤维增强。改良的劲度、结构刚度。高模量、高延性。也可用于泡沫塑料面层仪表板。
Automotive interiors. 10% glass-reinforced. Increased stiffness/structural rigidity. High modulus/ductile. Foamed skin instrument panel uses also.
而以板底拉应力等效为指标的基层顶面当量回弹模量值能较为真实地反映基层刚度和厚度变化对板底拉应力的影响。
But the principles of stress equivalence could accurately reflect the influence on the cement concrete pavement stress by the modulus and thickness of semi-rigid type base.
考虑刚度劣化后，剪切带的弹性应变由弹性剪切模量、损伤变量及残余剪切模量确定。
Elastic shear strain in shear band was dependent on shear elastic modulus, damage variable and residual shear modulus.
结果等张编织组肌腱移植物刚度、弹性模量显著优于非等张组。
Results The stiffness and elastic module of tendon grafts were better in isotonic weaving suture group than in non-isotonic weaving suture group.
随着上层土模量增大桩顶复刚度的刚度部分也相应增大，阻尼部分相应减小。
Pile stiffness increases and damping decreases with increasing modulus of upper soil.
假体柄的刚度由制备材料的弹性模量决定且与直径的4次方成正比。
Stem stiffness depends on the elastic modulus of the material and is proportional to the fourth power of the diameter.
计算了含有纤维端头裂纹的单向短纤维复合材料的有效纵向拉伸模量和纵向剪切模量，并分析了体分比、刚度比、长径比等物理、几何因素的影响。
The self-consistent finite element method is used to evaluate longitudinal effective Young's modulus and shear modulus for unidirectional fiber composite containing the fiber-end crack.
织物硬挺度测试仪，可通过简单操作及计算求出织物的弯曲高度、弯曲刚度、弯曲模量。标准：ERT 50 - 2ASTMD1388 BS 3356。
Fabric by tester dull color. gives degrees operation and simple calculation out the fabric of bending height, bending rigidity, bending modulus. Standard: ERT 50-2 ASTM D1388 bs3356.
织物硬挺度测试仪，可通过简单操作及计算求出织物的弯曲高度、弯曲刚度、弯曲模量。标准：ERT 50 - 2ASTMD1388 BS 3356。
Fabric by tester dull color. gives degrees operation and simple calculation out the fabric of bending height, bending rigidity, bending modulus. Standard: ERT 50-2 ASTM D1388 bs3356.
应用推荐