切割深度可自动控制调整深浅。
Cutting depth can be controlled automatically adjust shades.
当我厂多个部分的一个单一的板我通常设置切割深度，以假约。
When I mill multiple parts out of a single plate I usually set the cutting depth so as to leave approx.
根据断裂带切割深度，认定这两个断裂带均为超壳断裂，且都有岩浆上涌。
According to dissecting depth of the zone of faults, the two zones of faults with upwelling of magma were transcrust (crust-upper mantle zone of faults).
对混凝土试块进行切割实验，并对分析同切割深度的不同形态所产生的原因。
Experiments of cutting concrete block were conducted and the reason for different fonns on different cutting depth was analyzed.
这个模糊控制模型可以预测在任何给定一组加工参数时，可获得的切割深度。
This particular model predicts the depth of cut achievable with any given set of process parameters.
三维表面裂纹间的贯通要复杂得多，同时受裂纹切割深度、空间位置影响较大。
The propagation and coalescence of 3d surface cracks are dependent on the crack depth and the crack configuration.
论文从能量平衡的角度探讨了射流切割的过程，建立了水射流切割深度数学模型。
It discusses the water-jet cutting process by the balance of energy, and builds a mathematic model of cutting depth.
理论分析和试验结果表明切割深度随着切割速度的减小而增加，随着激光功率的增加而增大。
Theoretical analysis and experimental results all indicate that cutting depth is increasing with the decreasing of cutting speed and increasing of laser power.
按地壳性质和断裂切割深度，可再分为陆架陆壳断块、陆坡过渡壳断块和中央海盆洋壳断块。
According to crustal type and fault depth, the block may be further divided into shelf contin...
路面切槽机通过四连杆机构可以调整切割深度，采用切割卡轮，保证锯片不跑偏，保证切割准确。
Road cutting through the slot machines four linkage cutting depth can be adjusted by cutting card round, saw no guarantee that deviation, and ensure accurate cutting.
采用CO2激光切割模切板，研究激光功率、切割速度、焦点位置等参数和切割深度之间的相互关系，研究如何确定最大切割速度和优化切割速度。
CO2 lasers is conducted to cutting die - board with the aim of discussing the relationship between cutting depth and parameters such as laser power, cutting speed and focal position.
没有复杂的拨盘或者开关，只有一个很直观的切割功能，可以自动根据需要的钻孔深度调整设定。
No complex dials or switches – just an intuitive slide mechanism that automatically adjusts settings based on the desired depth of drive.
按客户要求的规格和形状在硅片表面切割出具有一定深度的沟槽。
Cutting groove grids on wafer surface in a special size and shape depends upon the costumers needs.
适合变化的切削深度和适合间断性切割。
在硬件纹理加速体重建算法的基础上，提出了两种模拟三维数据切割的方法：利用深度缓存实现和利用离散距离场实现。
Based on hardware-accelerated texture-based volume rendering algorithm, this paper proposed two methods for volume cutting, which are based on either depth buffer or discrete distance field.
不过深度炭化木防腐作用是否会因为切割而受到破坏？
But whether the depth of carbonization wood preservative effect will be destroyed because of cut?
而横向沟谷的深度切割为岩体开裂提供了空间和临空面。
There are enough space and free surfaces for mountain body cracking with latitudinal valleys deep incision.
适合不同切削深度和间断性切割。
提供了一套线性聚能装药侵彻深度计算公式及线性聚能切割器设计参数计算方法。
A series of formulae on penetration depth of linear shaped charge and the calculation method on design coefficient of linear shaped cutter are provided.
过小的气体流量则使等离子弧失去应有的挺直度而使切割的深度变浅，同时也容易产生挂渣；
The too small gas flow makes plasma arc lost due to the degree and straight cutting depth becomes shallow, but also easy to produce hang slag;
分析结果表明， 纤维切割过程中，切断刀锋利性能的变化主要与切断刀的初始刃口半径、刃口角度、刃口的磨损量以及刃口上缺口的深度有关。
The result shows that the cutter blade edge radius, edge angle, the linear abrasion and the edge notch depth are main factors affecting its sharpness.
在ST12冷轧板上用线切割加工出不同深度的狭缝来模拟钢板中缝类缺陷。
Slots with different depth were made by WEDM in metal sheet of ST12 to simulate slot-type defects.
在ST12冷轧板上用线切割加工出不同深度的狭缝来模拟钢板中缝类缺陷。
Slots with different depth were made by WEDM in metal sheet of ST12 to simulate slot-type defects.
应用推荐