产品包括移液器、分液器和离心机，以及微量离心管和移液吸头等耗材。
Its product range includes pipettes, dispensers and centrifuges as well as consumables such as micro test tubes and pipette tips.
风速、分液器对其性能均有影响，同时集气管的形状、尺寸对它也有一定的作用。
At the same time shape and size of the discharge pipe have a certain effect.
依据两相流理论，分析了分液器安装角度、流型、液相表观质量流率与流量偏差之间的关系。
The relation between mass flow deviation and setting Angle, flow pattern, liquid apparent mass flow rate is analyze based on the theory of two-phase flow.
本文介绍了分液器性能实验装置及实验方法，并对改进型分液器的流量分配性能开展了研究。
In this paper an experimental equipment and experimental method for distributor performance are introduced. Performance of a new type of distributor is investigated experimentally.
RonHood把美国缅因州刘易斯顿家里的地下室用来放置并展示他收藏的PEZ分液器与商品。
The basement of Ron Hood's home in Lewiston, Maine has been fitted to display his collection of PEZ dispensers and merchandise.
没有一个救助机构会向海地北部派发医疗用品，这个问题现在十分紧急。我们需要抗生素、消炎药、止痛药、静脉液、骨折固定器、拐杖，也许还得加上医生。
We need antibiotics, anti-inflammatories, analgesics, IV fluids, antibiotics, casts, crutches... plus volunteer doctors.
整个设备可分为加热蒸发室、加热夹套、汽液分离器、搅拌器等四部分。
This equipment is composed by four parts: evaporation room, heating jacket, vapor-liquid separator and stirring device.
实践证明合理地设计及应用气液分离器，对提高空调产品的可靠性具有十分重要的意义。
Practice proved that design and apply the gas-liquid separator legitimately have a very important signification to improve the reliability of air conditioner product.
在综合分析切割粒径、压降、效率和分股比数学模型的基础上，建立了旋液分离器的设计模型。
Based on synthetically analyzing models of reduced cut size, pressure drop, efficiency and flow split, the design model of hydrocyclone separators has been developed.
分析了脱脂液中油分的来源及存在状态，介绍了常用油水分离器的原理和结构特点。
The sources and states existed of the oil in the degreaser are analyzed. The principles and structure characteristics of the common oil-water separator are introduced.
因此，结合分子蒸馏液膜传质和传热过程，研究蒸发区间稀薄气体的运动规律对工艺优化和分子蒸馏器放大生产具有十分重要的意义。
Therefore, combined with mass and heat transfer in liquid film, it is important for optimizing operation condition and enlarging equipment to study rarefied gas flowing in distillatory.
为提高连铸坯的质量，提高经济效益，对连铸机结晶器的液面进行检测控制十分必要。
It is necessary to detect and control the mould level for improving slab quality and economic benefit.
以某钢厂宽板坯连铸结晶器为研究对象，利用商业软件PHOENI CS建立一个三维有限差分模型，模拟宽板坯连铸结晶器内钢液的流动分布。
The fluid flow in a wide slab continuous caster mold was simulated by a three-dimensional model set up using the commercial software PHOENICS.
火炬系统配备分液罐、水封罐、火炬筒体、分子密封器、火炬头、长明灯、高空点火器、地面点火器、精密过滤器、塔架等。
The flare system is equipped with knock-out drum, seal drum, stack, molecule airproof, flare tip, pilot and ignitor .
气压液动。五通定向控制阀。第1部分：不带电连接器安装接口。
Pneumatic fluid power - Five-port directional control valves - Part 1: mounting interfaces without electrical connector.
气压液动。五通定向控制阀。第1部分：不带电连接器的安装接口。
Pneumatic fluid power - Five-port directional control valves - Part 1: mounting interfaces without electrical connector.
气压液动。五通方向控制阀。第2部分：任选电气连接器的安装接口面。
Pneumatic fluid power - Five-port directional control valves - Part 2 : mounting interface surfaces with optional electrical connector.
主要产品有：船用齿轮箱、船用辅机、液压离合器、液压离合分动箱、液粘调速离合器、减速机、真空泵等。
Main products: vessel gear case, hydraulic pressure clutch, hydraulic pressure double and branch driver, timing clutch, reducer, vacuum pump etc.
没有运动部件液位控制器有各种版本，并十分耐弄脏。
Level controllers without moveable parts are available in various versions and are extremely resistant to soiling.
施加0.5 T的磁场使结晶器内金属液的表面流速最小，这一计算结果与实验结果十分吻合。
And the surface velocity of molten metal in the mold was minimal at a magnetic flux density of 0.5 t, it agreed well with measured surface level fluctuations in water modeling.
施加0.5 T的磁场使结晶器内金属液的表面流速最小，这一计算结果与实验结果十分吻合。
And the surface velocity of molten metal in the mold was minimal at a magnetic flux density of 0.5 t, it agreed well with measured surface level fluctuations in water modeling.
应用推荐