本仪器采用比较准确的平均电阻率模型以及六电极分段测量方法。
The apparatus introduced in this paper was made according to resistivity model using a practical six-electrode technique for segmental BIA.
为满足大范围现场原位节理表面形貌的量测需要，提出了表面形貌的分段测量理论。
To meet the need of the in situ measurement of superficial morphology of joints in a large extent, the sectional measurement theory of the superficial morphology is suggested.
为避免产生光子并合现象的产生，可以利用在接收光路上加装中性衰减片、提高光电倍增管开始工作的高度和降低光电倍增管增益等措施来分段测量，提高臭氧测量的精度。
To avoid the phenomena of photon overlap, many measures such as neutral optical attenuator, gate witch and reducing the gain of PMT, are taken to enhance accuracy of ozone measurements.
当使用序列'b '发送该分段的时候，测量新的RTT，使用当前时间减去存储的时间戳。
You measure new RTT as current time minus the stored timestamp when the segment with sequence 'b' was sent.
基于误差预处理技术的纯方位目标跟踪方法，采用多项式分段拟合测量。
The tracking method of pure orientation target was based on error pretreatment, and adopted polynomial segmentation fitting to measure.
研究的对象是基于激光三角测量法获得的船体分段面三维数据。
The research aims at a data of the ship body that acquired according to the triangle diagraph method of laser.
并在实验基础上提出了采用分段标定及对环境温度补偿结果进行修正的方法，提高了测量精度。
To improve the measurement accuracy of the thermometer, the calibration for different ambient temperature and the correction of ambient temperature compensation are presented.
同时，采用滤波算法和分段曲线拟合等方法对电能表测量结果进行了优化处理，提高了测量精度。
In addition, by adopting filtering algorithm and sectional curve fitting, etc., the measuring results of energy meter are optimized to implement highly precise measurement.
通过采用分段式水位传感器，实现了水位测量和显示低成本设计；
The low cost design of water-level measuring and display was put out by using subsection water-level sensor;
通过比较新型分段检测辊与常见分段检测辊的结构特点，得出新型检测辊是一种测量精度较高，安装使用方便的测力元件。
It is obtained that the new separated roll is a kind of detecting load instruments which is more accurate and more convenient in installation by contrast with other separated roll.
本文采用观测值曲线的分段拟合方法，对北京地区部分断层位移测量资料进行处理。
Using separation stage for fitting of observational curves in this paper, the surveying data of fault displacements of Beijing area has been analyzed.
通过测量各分段电容传感器然后对测得的数据进行分析处理得到各界面位置是本论文的总体思路。
By measuring the capacitance of sub-capacitor sensor then processing the measured data to get the interface position is the overall idea of this paper.
该方法易于实现，通过对已知的标准工件进行测量实验，证明提出的标定方法是有效的，能够满足船体分段数字化测量的精度要求。
By measuring experiments of known standard parts, the easily realized method is proved efficient and can meet the precision requirements of digital measurement system for hull block.
结合实际分析了分段绝缘地线对线路零序参数的影响以及在线路参数测量时要注意的问题。
In this paper, the influence of the sectional insulation earth wire on the zero sequence parameters is analyzed in theory.
我国目前主要仍采用长平晶组分段互检方法作为直线度检定基准，测量精度不高(特别是在测量大尺寸零件时尤为明显)。
At present, long optical flat is still mainly adopted as calibrating benchmark in straightness measurement, whose accuracy is not so high (especially in measuring great-size parts).
依据测量所得的掺气浓度与流速资料，采用分段求和的方法得到的断面统计流量与实际流量的误差很小，表明测量结果是可靠的。
On the basis of experimental data of air concentration and velocity, the discharge of each transverse section is got by means of stereometry.
根据统计分析结论，使用分段拟合的方法对氨法脱硫的光谱进行计算，有效的提高了脱硫后数据的测量精度；
The calculation of the desulphurization spectrums is done by the use of the polynomial fitting in different sections, which increases the desulphurized data accuracy effectively;
根据统计分析结论，使用分段拟合的方法对氨法脱硫的光谱进行计算，有效的提高了脱硫后数据的测量精度；
The calculation of the desulphurization spectrums is done by the use of the polynomial fitting in different sections, which increases the desulphurized data accuracy effectively;
应用推荐