冉阿让的特长便是能直登陡壁，在不易发现的凸处找出着力的地方。
To climb a vertical surface, and to find points of support where hardly a projection was visible, was play to Jean Valjean.
新板的足球，与以往往的足球有所不同，其表皮不是由14块组成，而是8块组成，因而此种表皮的足球，其粘合处的凸脊具有特殊的空气动力学特征。
The new model is made out of eight panels, compared with the previous 14, and has special aerodynamic ridges on its surface.
植株灌木型，茎多分枝，可长至50厘米高或更高，茎干8到15毫米粗，淡绿色，有白霜，近根处色深暗，叶痕呈双凸形。
Plant shrubby, caudex branching, to 50 cm tall or more, 8-15 mm thick, pale green and glaucous above, darker below, leaf scars lenticular.
植物非光滑叶表形态中凸包处硬度较凹坑处的硬度大；
The hardness of convex hull is higher than that of pit portion on the sculptured leaf surfaces.
凸体的混合体积理论提供了统一处理各种不同的重要的几何量的方法，比如体积和表面积等。
The theory of mixed volumes provides a unified treatment of various important metric quantities in geometry such as volume and surface area.
目的探讨青少年特发性脊柱侧凸患者后路髂棘处取骨并发症的发生率。
Objective To explore the morbidity of the complications of posterior iliac crest bone graft in adolescent idiopathic scoliosis.
目的：介绍一种新的手术技术，通过颈椎骨折处迅速矫正后凸畸形。
Objective. To present a new surgical technique for acute deformity correction through cervical fractures in the setting of kyphotic deformities.
方法：在枕外隆凸下缘中点处作T字型切口，去除左侧枕骨。
Methods Make in the next the middle point of the type of t slice, do away with the left side Occipital bone.
研究表明不同可控拉深筋路径对盒形件侧壁和凹模圆角部位的应变路径影响不大，而对凸模圆角处的影响较为显著。
The results show that the different CD moving paths have little effect on the strain paths of box sidewall and die corner, which have significant effect on punch corner.
初次模拟显示，在阶梯轴的凸台处与其临近连接的阶梯轴段会产生缩孔、缩松缺陷。
The initial simulation indicated that the shrinkage defects formed at the boss sections and the section near the connection of multi-diameter shaft.
结果表明，凸模和凹模交界处的板料首先变形，应力及应变最大值出现在凸模圆角部位外侧板料上。
The results show that the sheet in the adjacent area of die and punch deforms primarily. The maximal value of stress and strain appears in the sheet of outboard punch round corners.
筋板、凸台部分或薄壁处为防止冷隔，要提高铝液流动性。模温应相对提高。
The number of stiffened plate, convex platform part or to prevent cold-lap thin-walled place, must improve liquid aluminum liquidity. Mould temperature should be relative improve.
所述管状空腔和下部空 腔贯通，连接处设有对前轮支撑管限位的条状卡凸。
The tubular cavity is communicated with the lower cavity, and a junction is provided with stripy fixture blocks limiting the positions of the front-wheel support tubes.
在支撑臂定位座的上壁顶口处对应支撑臂的滑动槽设置凸形滑动块；
The location slider of the support arm is cooperated to the sliding-groove of the sliding column to form to sliding mechanism.
另在定寸凸部上每隔适当距离处形成有延伸至衔接部的缺口槽。
Notch grooves which are extended to the join part are formed on the dimension raised part in the interval of a proper distance.
另在定寸凸部上每隔适当距离处形成有延伸至衔接部的缺口槽。
Notch grooves which are extended to the join part are formed on the dimension raised part in the interval of a proper distance.
应用推荐