索穹顶结构是大变形柔性组合结构,其受力分析属于几何非线性问题,求解较复杂。
Cable dome is a large deformation composite structure consisted of flexible cables. Its analysis is a geometric nonlinear problem and is difficult in its solution.
分析中采用了动力方法,考虑了几何大变形和冲击作用的影响。
The effects of geometric large deformation and impact action were taken into account in dynamic analysis.
文中应用简单高阶剪切层合理论和大变形理论对各向异性纤维增强的矩形橡胶复合材料层合板进行了几何非线性分析。
Using the Simple High order Shear Deformation Laminate Theory and large deformation theory, the geometric nonlinear analysis of rubber rectangular composite laminate plate is presented.
采用大变形几何非线性有限元法分析强夯加固机理及其振动对环境影响。
The geometric nonlinear finite element method is used to analyze the impact mechanism of dynamic compaction.
本文用有限变形理论对人工冻结壁施工的几何非线性和冻土蠕变材料非线性问题进行了非线性数值分析。
This paper applies the theory of limited deformation analysis to the non-linear problem of the geometrician and creeping material for the frozen-wall.
最后,本文以实例分析讨论了横向剪切变形、开孔大小、线布载荷位置和几何参数对临界载荷的影响。
Finally, some examples are given to show the effect of shearing deformation, the hole size, the position of linear load and the geometrical parameter on the critical load.
考虑地基弹性变形影响,用能量法对高桥墩进行几何非线性分析。
Using energy method, the geometric non-linear of higher bridge pier is analyzed.
讨论了齿轮运动误差与模拟齿轮加工过程的关系;分析了齿坯几何偏心和变形对齿轮运动误差的影响;建立了左右齿廓形误差模型。
The effects of geometric eccentric and deformation of gear blank to motion errors is analyzed and an error model for gears left and right tooth profiles is built.
采用该分析模型,分析了桩身几何参数、桩顶荷载水平、混凝土弹塑性和桩侧阻软化效应对大直径超长单桩承载变形性状的影响。
The effects of shaft geometry, load level, concrete elastoplasticity and shaft resistance softening on bearing and deformation characteristic of LDSLP were studied by using this model.
本文对大变形理论网格法技术以及与网格应变分析相联系的几何模拟法进行了深入的研究。
In this paper, the technology of large deformation square grid and the geometrical simulation which is closely allied with the square grid strain analysis, are studied deeply.
分析了加捻纤维束的变形几何关系,利用能量法揭示了加捻对纤维束性能参数的影响。
The geometric relevance to deformation of the twisted fiber bundle was analyzed and the influence of twisting on performance parameters of the bundle was revealed by energy method.
该标架系统可建立两条同源曲线几何不变量之间的解析关系,用于变形过程几何结构改变的分析。
The frame with its formula can set up analytic relationships among the geometric invariants of two homologous curves, and can be used to analyze the deformation process of geometric structures.
分析中包括了搭板的几何尺寸、材料因素、地基非均匀、枕梁及沥青加铺层对搭板弯拉应力及变形的影响。
The influence of geometric size, material properties of the slabs, inhomogeneous subgrade, sleeper beam and bituminous overlay on the bending stresses and deflection is investigated.
分析了齿坯几何偏心和变形对齿轮运动误差的影响;建立了左右齿廓形误差模型。
The effects of geometric eccentric and deformation of gear blank to motion errors is analyzed and an error model for gear's left and right tooth profiles is built.
通过对切屑截面几何、变形状态及切削比的实验分析,研究了非自由切削的变形特征。
The deformation characteristics of non free cutting (NFC) are experimentally studied with the chip cross section geometry, the deformation configuration and the cutting ratio.
分析结果表明,在一定几何条件下,T形相贯节点可以看作刚接节点,但应考虑一定的节点柔性对整体结构变形的影响。
The results show that the T-type connection joint can be regarded as rigid under some circumstances but the effects of certain joint flexibility on the structure system should be taken into account.
结构部分以四边形平板壳元为基础,采用更新的拉格朗日(UL)方法分析结构大变形引起的几何非线性问题。
The structural analysis is based on a quadrilateral flat-shell element and an updated Lagrange (ul) formulation, which can be employed to model geometric nonlinearities arising from large deflections.
球面离散格网模型单元的面积、形状是否相似关系到模型的精度,因此定量分析单元的几何变形、分布规律等是格网模型建模的重要组成部分。
Whether the area and the shape of the discrete global grids model units are similar to each other affects the precision of the model.
从圆弧齿轮齿面微分几何分析、弹性接触变形和跑合磨损分析,建立了具有二维表面速度的点接触弹流基本模型。
Based on the fuzzy mathematics and the theory of the reliability design, the mathematics model of the fuzzy reliability design of the circular arc gears is established.
应用几何图形,分析了变形轴中心孔与其最大内接圆柱体的关系;建立数学模型,计算了变形轴打中心孔时机械定心基准面的最佳位置。
Applying geometric figures, the paper analyzed the relationship between the central holes and the maximum inscribed cylinder of a deformed shaft;
应用几何图形,分析了变形轴中心孔与其最大内接圆柱体的关系;建立数学模型,计算了变形轴打中心孔时机械定心基准面的最佳位置。
Applying geometric figures, the paper analyzed the relationship between the central holes and the maximum inscribed cylinder of a deformed shaft;
应用推荐