几何修正了在显示器上，目前来源的一部分虚编辑。
Bugfix on the display of the imaginary part for current-sources in Geometry edit.
且当探针位于试片边界附近时，可在不需要进行边界几何修正的情况下进行测量。
Besides, it needs no boundary geometry modification to the film thermoelectric material while the probe locating at the boundary.
我们也得到在广义服务时间内服务台发生故障次数的分布，证明它服从一个修正的几何分布。
We also obtain the distributions of failure number which server takes in a generalized service time, and show that it follows a modified geometric distribution.
本文对牛顿万有引力定律提出了一种非黎曼几何的相对论性的可能修正公式。
In this paper, a possible Correction of non-Riemannian geometric relativity is made for Newton's Law of Gravitation.
基于微分几何和空间啮合理论，分析了修正型圆环面双包络环面蜗杆副齿面形成原理。
Analysis of the forming principle of tooth flank of modified type worm gear pair was based on different geometry and spatial engaging theory.
利用计算机程序，对形式的各种几何参量进行设定、修正，研究其空间的拓扑结构。
By computer programs, various geometric parameters for the form are set and revised and the topologic structure of the space of the form is researched.
在此基础，返回几何模型建立界面，直接对其危险截面进行修正，提高了整个行星架的承载能力。
On the basis above, we return the geometric model and do an amendment for its dangerous section to improve the carrying capacity of the whole planet frame.
文中推导并得到了在弱耦合极限下几何相位的最低阶修正的解析解及一般情况下的数值解。
In the weak coupling limit the lowest-order correction to the geometric phase is derived analytically and the general case is calculated numerically.
利用距离误差模型构造出机器人本体的约束方程，并求解出机器人的实际几何参数，进而将该参数应用于修正系统的运动学模型。
Constraint equations were constructed by using distance error model, and the actual geometric parameters of the robot were solved, and then these parameters were used in the modified kinematics model.
本文在广泛的几何条件下用大量数值模拟实验的方法证明了对任意几何形状，这种修正形式与几何尺寸无关。
Under general geometry conditions, it is proved through a great deal of numerical simulations that the correction form is independent of the geometry of the radiate material.
对于实际壳体，无论敷瓦还是未敷瓦都应采用修正的四参数几何亮点模型计算目标强度。
For the actual shells, the modified geometrical highlight model with four parameters should be used whether it is coated or not with silent tiles.
推导出典型几何计数器中子探测效率及热能谱修正系数。
The detection efficiencies of typical slow neutron proportional counters and the correction coefficients for Maxwell spectra are deduced.
阐述了双头涡旋型线几何结构参数及其修正的必要性。
Then expatiate the geometry structure parameter and the ponderance of modification wrap.
根据相对运动学原理建立了捏合块几何形状数学模型，并根据实际运转条件，对捏合块的几何形状作了修正。
The kneading block geometry is calculated comprehensively according to kinematics principle and modification of geometry is made to satisfy the practical running condition.
通过三维光弹实验测定了轴表面横向半椭圆裂纹的应力强度因子（SIF），并计算了与光弹轴裂纹几何及当地应力相对应的无限大体的SIF，从而求得SIF修正系数。
The SIF and its correction factor of the transverse surface semi-elliptic crack of a photoelastic axle are tested and studied with the method of three dimensional photo-elastics.
试验结果表明：水力空化对若丹明B确实有降解作用，处理系统中存在最佳的孔板几何参数和操作运行条件，并且若丹明B的降解速率随修正空化数的减少而增大。
There are the optimal geometric parameters and operating conditions in the system and the degradation rate of rhodamine B increases with decreasing the value of the modified cavitation number.
在前述方法的基础上，提出了拱桥承载力的评定方法，即先利用单荷载工况建立基于挠度残差值的目标函数，修正模型的弹性模量和几何参数。
At first it sets up objective function on the basis of the deflection difference of the single working and updates the elastic modulus and geometric parameter of the model.
基于修正的拉格朗日描述，系统推导了三角形平面壳单元用于几何非线性问题分析时的增量平衡方程。
Based on the updated Lagrangian description, the incremental equilibrium equations of triangular plate shell elements for geometrically nonlinear problem are derived.
本文用试验的方法显示了悬停状态旋翼的尾迹几何形状，并以试验结果为依据对现有的尾迹几何模型进行了修正。
The wake geometry feature of helicopter rotor in hovering is visualized by experimental method in this paper and the preceding wake geometry model is updated according to the experimental results.
SFMRUI利用冗余信息间的几何关系，以及冗余信息与误差间的隐含关系来修正误差。
SFMRUI USES the geometric relationships among the redundant information and the implicit relationships between the redundant information and the error to correct the error.
修正了对几何重叠线检查在这过程中悄悄5.7.1版本。
Bugfix for Geometry-Check on overlapping wires which crept in during version 5.7.1.
修正了对几何重叠线检查在这过程中悄悄5.7.1版本。
Bugfix for Geometry-Check on overlapping wires which crept in during version 5.7.1.
应用推荐