直齿共轭内啮合齿轮泵是一种新型低噪声液压元件。
Straight conjugate internal gear pump is a new kind of hydraulic component with low noise.
内啮合齿轮泵有两种齿形即：渐开线齿形和摆线齿形。
Internal gear pump has two kinds of tooth profile namely: involute profile and cycloidal tooth profile.
本文介绍了内啮合齿轮泵齿轮设计的准则及应注意的几个问题。
This paper introduces the criterion and some noted problems of gear design for internal gear pump.
这两种内啮合齿轮泵的工作原理和外啮合齿轮泵的工作原理相同。
These two kinds of internal gear pump working principle and external gear pump working principle the same.
留有开口的半环形轴承，用于内啮合齿轮双端支承及定轴齿轮箱。
A semi-annular bearing with an opening is used to support both ends of inside engaged gear or for fixed-axle gear box.
德国制造的内啮合齿轮泵的使用，保证整体系统噪音低，寿命长。
The inner engaged gear pump manufactured by a famous Germany company is used to reduce the system noise and extend the service life.
内齿轮在工业中应用十分广泛，对内啮合齿轮传动的特点进行了分析。
It is very extensive that the interior gear wheel is used in industry.
大模数大直径内啮合齿轮的加工，目前在国内是一个急待解决的难题。
Processing of large module and large diameter internal meshing gear is a problem which is anxious to be solved at present in our country.
为了解决这个难题，本文对大模数大直径内啮合齿轮精确成形方法进行研究。
To solve this problem, in this paper, the authors will study precise shaping method of large module and large diameter internal meshing gear.
内啮合齿轮泵中的小齿轮是主动轮，大齿轮为从动轮，在工作时大齿轮随小齿轮同向旋转。
Internal gear pump is the small gear wheel, the big gear for driven wheel, in work big gear with small gear cocurrent rotation.
通过分析计算及实验，结果表明，大模数大直径内啮合齿轮的这种精确成形方法比其它方法要好。
By analyzing, calculating and experimenting, it is shown that this precise shaping method of large module and large diameter internal meshing gear is better than any other methods.
渐开线齿形的内啮合齿轮，在小齿轮和内齿轮中间有一块月牙形状的隔板，目的是把吸油腔和压油腔隔开。
Involute profile of internal gear, in the small gear and internal gear intermediate have a crescent shape of the diaphragm, the purpose is the oil absorption cavity and pressure oil cavity off.
内啮合齿轮泵的结构和其他齿轮泵结构类似，主要由外转子、转子、泵轴、泵体、前盖、托架、密封装置、轴承等组成。
Internal gear pump structure and other gear pump structure similar to, mainly by the outer rotor and rotor, pump shaft, pump body, the front cover, bracket, sealing device, bearing, etc.
摆线齿形的内啮合齿轮泵又叫做摆线转子泵，泵中的小齿轮和内齿轮只相关一个齿，因此这种内啮合齿轮泵不需要设置隔板。
Cycloidal tooth profile of the internal gear pump, also called cycloidal rotor pump, pump the small gear and internal gear only related a tooth, so the internal gear pump do not need to set partition.
介绍了一种适用于少齿差内啮合行星齿轮变位系数的计算及选取方法。
A method of calculating and selecting modification coefficient of the internal gear with less teeth difference is presented.
计算了斜齿永磁齿轮机构的转矩和转速特性，同时研究了内啮合永磁齿轮的矩角特性曲线。
The characteristics of torque and rotational speed of skew gears are investigated and the characteristic curve of torque-angle of inside engaged gears are studied, too.
在此基础上导出了活齿与激波器、活齿与内齿轮啮合处的接触强度的公式；
Based on it, the formulae of contact strength of mesh points between the movable teeth and the surge wheel, the movable teeth and the internal gear are derived.
渐开线少齿差齿轮副，由于是内啮合，齿轮副的齿对之间的间隙很小，在受力后轮齿变形而使得同时有多对齿啮合。
As the gap of teeth of internal matins gears with small tooth number difference is small, several teeth will mate simultaneously after the teeth are deformed by load.
内啮合摆线转子齿轮油泵的齿形对泵的加工、性能(如：流量、脉动、噪声)等有很大的影响。
The gear form of internal gearing cycloidal gear pump has important influence on machining and characteristics of pump, such as flow rate, fluctuation rate and noise etc.
在获得齿轮内啮合传动的齿侧间隙计算公式以后，结合齿对刚度的计算公式，推导出齿轮内啮合传动的加载重合度及载荷修正系数。
After getting the formula about the normal backlash and the stiffness of the tooth pairs of the gear, the contact ratio and the load correction factor could be obtained.
通过几何分析的方法，导出了内啮合渐开线齿轮传动中心距略变小时，法向齿侧间隙的计算公式，供齿轮传动设计计算之用。
By using geometry analysis method, this paper educed calculation formula of normal direction gear side clearance when internal gearing involute gear transmission center distance waned slightly.
外啮合圆柱齿轮、内啮合圆柱齿轮、圆维齿轮和蜗轮蜗杆传动是齿轮传动的基本形式。
The basic types of gear transmission are external and internal cylindric gear drive, bevel gear drive, worm gear drive.
从而为内啮合直齿轮的接触强度及其可靠性分析奠定基础。
Thisestablishes the basis of contact strength and reliability studies of internal spur gears.
确定双内啮合渐开线行星齿轮减速器内齿轮副的设计参数，从制造到安装有许多限制条件。
To determine the internal gear pair design parameters of two-stage internal contact involute planet gear reducer all constrained conditions from machining to assembly must be satisfied.
行星轮与左右两个半内齿轮啮合时，属于不同的传动形式。
This mechanism are different transmission forms when the planetary gear meshing with the two semi-internal gears.
第二齿条，其被安装来在所述外壳内做直线运动，所述第二齿条与所述第二小齿轮啮合，以便所述第二小齿轮的转动直线地移动所述第一齿条；
A second rack is mounted for linear movement in the housing. The second rack engages with the second pinion gear such that rotation of the second pinion gear linearly moves the first rack.
但是，由于内啮合锥齿轮副的齿廓重叠干涉公式非常复杂，实际使用时计算量很大。
But the calculation is practically a very because of the complicacy of tooth-overlapping interference formulas.
介轮箱(11)内的上齿轮(16)、下齿轮(15)和介轮(13)是固定啮合连接。
A cog (16), a lower gear (15) and a medium gear (13) inside a medium wheel box (11) are fixed mesh connection.
介轮箱(11)内的上齿轮(16)、下齿轮(15)和介轮(13)是固定啮合连接。
A cog (16), a lower gear (15) and a medium gear (13) inside a medium wheel box (11) are fixed mesh connection.
应用推荐