此液压垫的最大公称力是4，500kN。
新闻报告说，她将要参加一个慈善活动，叫“勇敢的守护天使”，是向因公称职的警员致敬的活动。
A press release announces that she is set to attend a charity event called "Eagles and Angels, " which honors police officers killed in the line of duty.
指出螺栓联接的扭紧力矩值不仅与螺栓的公称直径及性能等级有关，还与能否保证联接可靠工作有关。
The value of tightening torque is relative not only to the nominal diameter and quality class of the bolt, but also to the security of the threaded fastener.
J 41 n型PN 40钢制截止阀：手动、法兰连接、直通式、阀座密封面材料为尼龙塑料、公称压力pn 40、阀体材料为碳素钢的截止阀。
J41N Type PN40 steel globe valves: manual, flanged, straight-through, the valve seat sealing surface material as nylon plastic, nominal pressure PN40, carbon steel valve body material cut-off valve.
流道孔径与阀门公称通经，基本相同的为全通径式；流通孔径比阀门公称通经小的称为缩径式。
Nominal diameter and flow valves, basically the same breath for full-bore type, Circulation than nominal diameter valve is given. it small called non-reducing type.
钢板按理论重量交货，用公称厚度加表2所列的附加值作为计算重量的理论厚度。
Plates shall be ordered to theoretical weight, the added value to nominal thickness listed in Table 2 plus nominal thickness shall be the theoretical thickness for weight calculation.
对比试块应从与待检材料有相同的公称外径、材质和热处理状态的棒或管上制取。
The reference standard, of convenient length, shall be prepared from a length of bar or tube of the same nominal outside diameter, material and heat-treatment as the material examined.
而折边锥形封头一般焊接于两公称直径不同的筒体中间，使两公称直径不同的筒体连为一体！
While ruffled tapered header general welding in two different nominal diameter of cylinder, make two nominal diameter of different cylinder is an organic whole repeatedly!
本文对产生这种差别的原因进行了分析，并给出了从空气测量数据到实际公称容量值的换算关系。
The reason of the difference is analyzed and the conversion formula from the air test value to the real capacity is given in this paper.
它必须安装在公称压力不超过这个额定压力的管道系统中。
It must be installed in a piping system, where the normal pressure does not exceed this rating.
文章分析了精锻工艺的可行性，介绍了高能螺旋压力机公称压力值的计算方法。
The paper analysis the forging craft of rocker shaft bed part, introduce the computing technology of high energy screw press apparent pressure value.
接线端应该设计到位才能保证不会无缘无故的被塞进管子内，或者，采用相同的公称尺寸，这样一种方式才能确保接线端自由出口处不会受到限制。
A terminal shall be so designed that it cannot be inadvertently pushed onto a pipe or fitting of the same nominal size in such a manner that the terminal outlet free area is restricted.
为优化装配系统中公差链的公差值，建立了几何尺寸公差的优化模型，并提出公差的分层优化设计算法：第一层，解决设计公称值居中的优化问题；
In order to optimize tolerance values for an assembly system, a model for geometric dimension tolerance optimization was established and an algorithm for optimal tolerance design was proposed.
特别检察官办公称，那些邮件里含有关于三星提供的财务支持的信息。
The emails contained information about the financial support provided by Samsung, the prosecutor's office said.
主要提出以下观点：锅炉吊杆用螺母的高度与螺纹公称直径之比不宜小于1。
Presents the following viewpoints:the radio between the height of the nut for boiler hanger rod and the diameter of screw shall not be less than 1.
注：（1）公称流量是水表在规定误差限内允许长期工作的流量。
Note:(1)Rated flux is the permitted flux in the long work situation for the water meter.
针对断面尺寸偏离图纸公称尺寸的情况和噪声的存在，给出了识别正确性的理论分析。
The accuracy of the method is discussed in theory, given the deviation of profile dimensions from their standard dimension and the existence of noise.
使用适量的焊料：如果使用线状焊料，那么对公称通径为3/4英寸的阀门就要采用3/4英寸的焊料，等等。
Use just enougn solder: with wire solder, use 3/4" for a 3/4" valve, etc. If too much solder is used, it may flow past tube stop and clog sealing area.
对于公称通径大于8英寸的蝶阀，如果是在液体中使用，则在关闭阀门时，动态扭矩有比较明显的增加。
Butterfly valves, sizes 8 "and larger, when used on liquids, show a marked increase in dynamic torque which tends to close the valve."
对于公称通径大于8英寸的蝶阀，如果是在液体中使用，则在关闭阀门时，动态扭矩有比较明显的增加。
Butterfly valves, sizes 8 "and larger, when used on liquids, show a marked increase in dynamic torque which tends to close the valve."
应用推荐