公式变形策略；
从弹塑性理论出发以圆截面轴为例对校正应力与残余变形进行了分析研究，提出了在给定弯曲误差下的校正载荷的计算公式。
The paper has studied straightening stress and residual deformation of circular shaft by using elastic - plastic theory, deueloped calculation formula of straightening loud in given deflection error.
针对交通荷载作用下软土地基的变形问题，采用累积应变的经验公式计算其累积沉降。
Using an empirical cumulative plastic strain formula, a method for calculating the traffic load induced deformation was proposed.
文中以球体静态接触为对象，建立模型并推导出赫兹接触应力、变形公式。
Sphere contact as object, contact stress and distortion formula of Hertz are deduced theoretically from the modeling.
其次，由轴向定位预紧轴承受径向载荷时各滚子的变形，推导出轴承的径向刚度计算公式；
Second, the calculation formula of radial rigidity is deduced according to the deformation of rollers under the radial load with axial position preload.
文中首先介绍了散斑图像相关数字技术的基本原理，然后给出了变形计算公式。
The basic principle of speckle image correlation digital technique was introduced firstly in this paper. And Calculation formula of deformation was also presented.
利用俄亥俄州永久变形模型，推导出用于求多级荷载下路面车辙深度的计算公式。
An equation for pavement rutting depth under multi-load is derived by using Ohio state permanent deformation model.
通过对其结构设计、工作原理的论述，建立受载变形公式，分析其参数间的关系。
Through discussion of the structure design and operating principle, the equation of deformation under load is established and the relationship between parameters is analyzed.
从圆柱形零件的凸缘上和壁上的允许变形出发，获得了极限拉伸程度的计算公式。
The formulas for calculating top limitation of drawing originated from the deformation limits on the flange and the wall of cylindrical articles are developed.
本文给出了考虑剪切变形引起的挠度计算公式，对现代机床的主轴设计具有一定的指导意义。
This paper puts forth the calculating formula of the deflection caused by shear distortion, which has a reference value to the design of the main shaft of the machine tool.
由理论分析所得变形力分布计算公式与实验结果相吻合。
The distribution of deformation force calculated by the formula based on theoretical analysis coincides well with the experiment result.
文中首先介绍了散斑图像相关数字技术的基本原理，然后给出了变形计算公式。
The basic principle of speckle image correlation digital technique was introduced firstly in this paper.
经过合理的简化，给出了壳的挠度与厚度同级的大变形基本公式。
The fundamental formula of large deformation, when the deflection is of the same order as the thickness of the shell, is derived based on rational simplification.
研究了变形体虚功原理的理论和建立方法，并将其用于建立接触问题有限元法计算公式。
The theory of virtual work principles of deformable bodies and the technique to derive their expressions are studied and applied to contact problems to build FEM formulas.
应用理论公式对C型框架的变形位移量进行了验证，为永磁扭摆磁铁的结构设计和进一步改进提供了理论依据。
The displacement of the C_shape frame is calculated by the theoretical formula to provide a theoretical basis for further structure design and improvement of the permanent magnetic wiggler.
从理论上分析了滑动摩擦对接触变形的影响，给出了压陷量的修正公式，并通过试验加以验证。
This paper analyzes the influence of sliding friction on contact deformation in theory and demonstrates it by means of test.
提出了饱和粘土利用割线模量法计算固结沉降，且考虑侧向变形影响的公式。
Firstly, the paper puts out the formulas used to calculate displacement by secant modulus, which think about the influence on lateral displacement.
基于试验结果，拟合出了考虑各关键参数影响的火灾下两跨连续梁边支座反力与梁跨中变形的计算公式。
Calculation formula of side support reaction and deflection in the mid-span of beams subjected to fire were obtained by fitting curves of experimental data considering each key factor.
根据应变协调条件，推导出了套管、水泥环及地层受力变形状态的计算公式。
According to strain coordination condition, the force and deformation state formulas of casing, cement loop and stratum are derived.
在径向未变形切屑厚度公式的推导中，考虑了刀具进给运动的三维特点。
The three dimensional characteristic of cutter feed motion is considered in the formulation of undeformed radial chip thickness.
在建立滑坡外部变形测边三维监测网的探讨中，推导出了变形向量的解算公式，并给出了精度估算公式。
In this paper, the formulae for the solution method of deformation vectors are derived and the precision formulae are also given.
分析了复合地基的各种计算方法之后，提出了采用综合变形模量的概念来计算复合地基变形的计算公式。
After analysising all kinds of settlement calculation method of PCPCF, the dissertation has come up with using composite deformation modulus to deduce the calculation formula of PCPCF.
根据膨胀变形试验结果，建立了膨胀土的膨胀量、膨胀速率以及膨胀变形所需时间与起始含水量的相关公式。
Based on test data, the formula correlative of time required for soil's expansive capacity, expansive speed rate and expansive deformation with initial moisture content is established.
应用薄板非线性理论的变分方法求解基本方程，得到了单片碟形弹簧的载荷和变形关系以及应力分布及其计算公式。
By the variational method, the governing equation of the plate non-linear theory is solved, and he relationship between load and deformation of a single spring leaf is obtained.
针对经验公式方法的不足，提出基于工程实例的隧洞最大允许变形的支持向量机(SVM)自动获取方法。
Aiming at the disadvantages of experience formula, the case-based SVM method for maximal deformation forecasting of surrounding rocks of tunnels is proposed.
文中以圆锥螺旋弹簧变形后的平衡位形分析计算其受力和变形，导出了非线性公式。
Here, force and deformation of a conical helical spring are discussed based on equilibrium configuration after deformation, and a nonlinear analytic formula is derived.
文中以圆锥螺旋弹簧变形后的平衡位形分析计算其受力和变形，导出了非线性公式。
Here, force and deformation of a conical helical spring are discussed based on equilibrium configuration after deformation, and a nonlinear analytic formula is derived.
应用推荐