安装顶部侧齿轮和离合器片组件。
主要从事新型无侧压无连杆内摆线行星齿轮内燃机的研制开发和经济管理软件的开发。
Mainly engaged in a new type of lateral pressure without cycloidal gear linkage within the internal combustion engine research and development of economic management and software development.
这种差别适合装配之间的车轴轴，与正在花键轴的差别齿轮一侧。
This differential assembly fits between the axle shafts, with the shafts being splined to the differential side gears.
齿轮的齿侧间隙直接影响数控机床的加工精度，因此，进给系统传动间隙的消除是机床数控改造的一项重要内容。
The tooth side slack of the gear influences the machining accuracy of NC machine tool directly, so, taking out the slack of feed drive gearing is an important item in the machine tool rebuilding.
用有限元方法，对双圆弧弧齿锥齿轮沿齿长方向齿根应力进行了计算。通过应力计算结果的分析，得出了凸、凹两齿侧应力沿齿长的分布规律。
Through the calculation of the finite element method(FEM) models for double circular arc profile spiral bevel gear, the stress changing pattern along the length of the tooth is obtained.
在获得齿轮内啮合传动的齿侧间隙计算公式以后，结合齿对刚度的计算公式，推导出齿轮内啮合传动的加载重合度及载荷修正系数。
After getting the formula about the normal backlash and the stiffness of the tooth pairs of the gear, the contact ratio and the load correction factor could be obtained.
广泛应用于汽车发动机、底盘、摩托车离合器、齿轮侧板和起重设备领域。
Widely used in auto engine, motorcycle clutch, gear flappers and hoisting equipment etc.
其中的每个小齿轮，提供卓越的动态负载能力轴一侧。
One on each side of the pinion shaft providing superior dynamic load capacity.
齿轮侧传动行走，液压振动，液压转向，三挡速度，转场方便；
Mechanical travel drive of side transmission, hydraulic vibration and steering with three-gears travel speed for convenient transport between construction sites.
通过几何分析的方法，导出了内啮合渐开线齿轮传动中心距略变小时，法向齿侧间隙的计算公式，供齿轮传动设计计算之用。
By using geometry analysis method, this paper educed calculation formula of normal direction gear side clearance when internal gearing involute gear transmission center distance waned slightly.
采用矩形侧浇口、齿轮齿条脱螺纹机构。
Rectangle-shape side gate and the gear-rack taking off thread mechanism were used.
齿轮在齿厚部位都是单侧磨损，所以可将齿轮翻转180度使用。
Gear tooth thickness at the site are unilateral wear, so gear can be rotated 180 degrees to use.
当车辆转弯时，齿轮使得一侧车轮比另一侧车轮旋转得更快。
Certain gears allow one wheel to turn faster than the other wheel when the vehicle is turning a corner.
采用数值模拟方法研究了含气比，侧板倾斜，有效体积模量，离心力和齿轮副的振动等因素对困油压力的影响。
The influence of percentage of gas in oil, slope of side plate, effective bulk modulus, and centrifugal force and gear pair vibration on trapped oil pressure is studied by numerical simulation.
由推导出的齿端和槽端面积及其圆心矩公式，首先得出轴套（侧板）内外两侧所受的力和力矩关于齿轮基本参数的函数表达式。
Based on both the area formula of gear tooth and groove and their respective center multiplying formula, the force and moment expressions of both sides of side-panels could be brought out at first.
结果通过测量获得骶髂关节面上任意点的高度，发现骶髂关节两侧关节面呈一种类似齿轮样相互咬合与滑槽轨迹相结合的关节面形态。
Results The height of any point on the surface was evaluated, and it was found that two sides of the sacroiliac joint surface showed reciprocal convexities or elevations.
本文运用热弹性力学原理，分析了温度变化对啮合齿轮侧隙的影响以及对齿厚偏差选择的影响。
Based on the thermal elastic mechanics, the influence of temperature change on the normal backlash was analyzed, and the deviation of teeth width was calculated.
得到了系统在不同的输入转矩波动、齿侧间隙、齿轮综合误差、激励频率和阻尼比参数下系统的全局特性。
The system's global characters are obtained under different input torque fluctuation, backlash, composite transmission error, exciting frequency and damping ratio.
齿轮相结合传动，即有顶装式又有侧装式。将水翼技术利用于搅拌桨设计上，为您提供适合您要求的搅拌桨形式。
MixPro utilizes proven hydrofoil technology for their impeller designs and can provide a full complement of impeller styles to suit your agitation requirements.
本文在分析各种影响齿轮副侧隙因素的基础上，讨论齿轮副侧隙的计算方法和步骤。
There are many influential factors for backlash of the gear pair. This paper studied various factors and discussed the calculating methods and steps on backlash of the gear pair.
此外，在进行运送和装配时每一个所述侧梁构件和所述端部横梁构件最好具有连到它们的滚柱道部分和环形齿轮部分。
Further, each of the side members and end cross members preferably has a section of a roller path and section of a ring gear attached to them while being transported and assembled.
减速齿轮传动机构基本上被密封，并且设置在相应的侧板内侧。
The reduction gear drive mechanisms are substantially sealed and disposed inside the corresponding side plates.
齿轮油泵在运转时主动齿轮带动被动齿轮旋转，当齿轮从啮合到脱开时在吸入侧(A)就形成局部真空，液体被吸入。
Gear pumps in operation when the passive gear driven rotary gear, when the gear was torn off from the mesh to the side when inhaled (a) on the formation of partial vacuum, the liquid to be inhaled.
需要进一步提高水压齿轮泵加工精度，特别是侧板以及齿轮端面的平面度、表面粗糙度以提高水压齿轮泵的性能。
Also the manufacturing precision of water hydraulic gear pump, especially gear surface and side flank, is required in order to improve its volume efficiency.
利用轮齿接触分析与齿轮啮合原理，建立了齿面均匀研磨与定点研磨控制的几何运动模型，经滚检检验，该模型能对齿面研磨位置与侧隙进行较准确的控制。
The rolling tests prove that this setup model can control precisely the displacement of the lapped area in the tooth surface and keep the even backlash.
此时，使扶起驱动轴(46)的花键部花键嵌合在内置于扶起齿轮箱(71)中的扶起侧伞齿轮(83)的花键孔中。
In this case, the spline part of a raising driving shaft (46) is spline-fitted to the spline hole of a raising side bevel gear (83) built in a raising gear case (71).
建立了两级星型齿轮传动系统的非线性动力学分析模型，模型中考虑了系统的综合啮合误差、时变啮合刚度以及齿侧间隙。
A dynamic analysis model in which the gear error and the time-varying stiffness and backlash are included is established for a 2-stage star gear train.
建立了两级星型齿轮传动系统的非线性动力学分析模型，模型中考虑了系统的综合啮合误差、时变啮合刚度以及齿侧间隙。
A dynamic analysis model in which the gear error and the time-varying stiffness and backlash are included is established for a 2-stage star gear train.
应用推荐