推荐使用应力敏感性系数来度量储层的应力敏感程度。
We state to use stress sensitive coefficient to characterize stress-sensitivity of different reservoirs.
最后使用应力场叠加方法分析了位错和界面的耦合效应。
Finally by using superposition methods the combined interaction of dislocations and interfaces is analyzed.
到目前为止，此测试与应力测试结合使用尚未得到批准。
To date, there is no approval for use of this test in conjunction with a stress test.
还有反应堆冷却剂系统焊接问题，它们使用了并且得到原生水,应力腐蚀裂痕。
There are reactor coolant system weld issues, they're used and they're getting primary water stress corrosion cracking.
然而这种方法很快就被副翼的使用取而代之。副翼是一种铰链连接的可动部件，能减少结构应力并提高飞机控制的灵敏度，深得人们的青睐。
That approach was quickly abandoned, though, in favour of ailerons-hinged moving parts that provide more subtle control and place less stress on the structure.
否则，你也可以使用一个较大的口模开口，以减少口模出口应力，然后把挤出物拉细到所需要的尺寸。
Or you can use a larger die opening to reduce die-exit stress, and then draw the extrudate down to the desired size.
通过适当的设计，可以使晶粒流动方向与实际使用时的主应力方向一致。
With proper design, the grain flow can be oriented in the direction of principal stresses encountered in actual use.
为了尽量减小这种效应产生的电流，重要之点在于消除绝缘子上的机械应力并使用压电效应和储存电荷效应最小的绝缘材料。
To minimize the current due to this effect, it's important to remove mechanical stresses from the insulator and use insulating materials with minimal piezoelectric and stored charge effects.
计算结果表明，在铺层分界面上有十分明显的应力峰，并发现，即使沿铺层厚度使用16个二次元素，这些值仍没有达到令人满意的精度。
The results show quite distinct stress peaks at layer interfaces, and it was found that even with 16 quadratic elements over the layer thickness these values have not reached an acceptable accuracy.
本文介绍了地应力测量所使用的测量方法、测量过程和测量结果。
This paper introduces the method, process and results of the in-situ stress measurement.
应力强度因子(K)：断裂力学中使用的一个因子，说明裂纹尖端处的应力强度。
Stress intensity factor (k). A factor used in fracture mechanics to specify the stress intensity at the tip of a crack.
在工程结构中使用的大部分材料最初的应力应变图是直线型的。
The initial portion of the stress-strain diagram for most materials used in engineering structures is a straight line.
对所使用的材料来说，与实际应力比较的容许应力是以实验研究结果为基础的。
The allowable stress levels to which the actual stress levels are compared are based on empirical findings for the material involved.
若使用会有残留应力现象的材料如PC时，残留应力会对量测结果造成影响，这是设计时应该注意的地方。
When we designing light guide plate, we should be careful on the effect of residual stress when using PC.
钢制容器人孔的焊接应力及塌陷变形，直接影响容器的焊接质量和使用寿命。
The notch welding stress and the collapse-deformation of steel container directly affects the welding quality and service life of the container.
该实验是在各项异性的固结作用后保持差应力，使用孔隙水控制装置在体积不变的应变控制条件下将孔隙水注入。
In the test, after anisotropic consolidation, keeping the deviator stress, pore water is injected using pore water control apparatus under a constant volumetric strain controlled condition.
本文对目前国内外使用的残余应力的测定方法进行了归纳。
In this paper, the determining methods of residual-stress which are being used at home and abroad are summed up.
另外，在预应力连续桥梁的使用过程中，发现箱梁开裂的现象相当严重。
Otherwise, in using the continuous girder bridge we can find that the craze of the box-beam is very popular.
他们还提到，由于担心以前的全细胞百日咳疫苗日渐增强的致反应力，因此不推荐对6岁以上年龄的青少年使用。
Previously vaccination against pertussis was not recommended for those over 6 years of age, they add, because of concerns of increased reactogenicity of the whole-cell vaccines.
热塑性工程塑料包装箱由于设计和加工工艺不当，在各种使用环境中易导致产品应力集中而开裂。
In some of usage environment, the engineering thermoplastics packaging case can cause stress concentration and cracking because of the bad design and processing technology.
张拉千斤顶、油表在预应力钢束张拉前进行检验和标定，使用中按规定程序进行送检标定。
Tensioning jack, oil gauge shall be checked and calibrated prior to the prestressed steel strands tensioning and executed to check and calibrate in using as per the specified procedure.
锐角会增加锻件中的应力，同时在使用时削弱锻模。
Sharp corners are stress-risers in the forgings, as well as make the dies weak in service.
然后确定了加速应力为影响气缸寿命的工作应力：流体温度、使用压力及气缸动作频率；
Then the determined accelerate stress is the stresses that affect the cylinder life as fluid temperature, working pressure and moving frequency.
目前，振动试验中使用的夹具，其传递的应力往往存在较大的失真。
The stress transfer distortion exists in current fixtures on the vibration tables during testing.
使用初应力法对非线性方程组进行迭代计算，避免了组装和分解总体刚度矩阵的繁杂而庞大的运算。
To cut down great calculation of assembling and disassembling of stiffness matrix in the nonlinear procedure, the initial stress method is introduced to resolve the nonlinear equations.
本文描述了等温应力松驰的检测方法及使用此方法对皮胶原的耐湿热稳定程度的研究。
Current research has been focused on the studies of isothermal tension and its relaxation, its relation and their application on investigation of the hydrothermal stability of skin collagen.
结果是表面更为平滑、接触应力降低和使用寿命延长。
The result is a smoother surface, lower contact stresses and an increase in service life.
已加工表面存在的残余应力影响工件的使用性能和疲劳强度。
The residual stresses impacts the working performance and fatigue strength of parts.
已加工表面存在的残余应力影响工件的使用性能和疲劳强度。
The residual stresses impacts the working performance and fatigue strength of parts.
应用推荐