对系统总体设计方案进行了研究分析，硬件设计中详细介绍了控制回路的电流检测模块、电机转速和位置检测模块、PWM输出和故障输入电路。
The overall design scheme is researched. The hardware of current detection module, motor speed and location detection module and PWM output and fault input module is introduced in detail.
针对扫描镜精密伺服系统，本文采用按照电流环、速度环和位置环等三个回路进行控制系统设计的开闭环复合控制方案。
The scanning mirror precise servo system is designed by the scheme of compound control of open and closed loops with current, velocity and position loops in this paper.
研究了弹性轨道条件下，控制回路中位置反馈信号存在时滞的磁浮系统在亚谐轨道激励作用下的响应问题。
The response of the Maglev system with delayed position feedback control under the sub-harmonic excitation of the flexible guideway is investigated.
介绍在仿真变电站断路器控制回路仿真设计中，如何利用双位置继电器解决断路器机构触点仿真设计的问题。
It is described in this paper that how to use two-position relay to solve simulation design of contact of CB in control circuit of simulation substation.
针对单回路电液位置伺服系统的动态特性，提出了一种等效流量反馈的控制方法，从而实现了串级控制。
This paper studies the dynamic characteristics of Electro hydraulic Position Servo System, and proposes a method of equivalent flow feedback to realize serial control.
本文对AT P系统位置回路搜索扫描的控制算法进行了比较详细的讨论，并给出了校正算法的差分方程。
The control algorithm about laser range orientation for ATP system is discussed and the difference equation is presented in this paper.
为实现对小车的位置和抓斗的摆动分别控制而设计了两个控制回路，其中一个回路采用常规的PID算法来调节小车的位置和速度，同时另一个回路则利用模糊逻辑控制器来消除抓斗的摆动。
Two control loops are devised: a conventional PID regular is used to control the position and velocity of the trolley, and a fuzzy logic controller is proposed to the anti-swing control of the load.
安装电机、变压器、控制器和照明器材到指定位置，并根据图纸描述完成整个回路。
Mounts motors, transformers, controllers and lighting fixtures into position and completes circuits according to diagram specifications.
位置回路采用PD控制算法，以增加系统相位裕度，减弱系统振荡，保证控制系统具有良好的动态特性。
The position loop use the PD control algorithm, to increase the system's phase margin, reduce the system's oscillation and ensure that the control system has good dynamic characteristics.
设计一种基于光电池的核废料沉淀罐沉淀界面位置检测装置，采用分布式组态plc系统作为控制终端，继电器控制回路作为冗余控制系统。
A distributive configuration PLC system was used as control terminal of the detection device, while a relay loop as a redundancy control system.
设计一种基于光电池的核废料沉淀罐沉淀界面位置检测装置，采用分布式组态plc系统作为控制终端，继电器控制回路作为冗余控制系统。
A distributive configuration PLC system was used as control terminal of the detection device, while a relay loop as a redundancy control system.
应用推荐