其次,根据位移协调条件建立滑动体的速度场,并计算各滑动楔块的位移速度;
Secondly, the velocity field was determined based on the conditions of kinematic admissibility.
跨断层测量的复测周期主要由观测精度和断层位移速度决定,二者合理匹配的周期就是最佳周期。
A repeated period of measurement across the fault is mainly determined by observation accuracy and rate of deformation. It is the best period for they to match reasonably.
然后引进差补方法计算物料平均轴向位移和平均停留时间 ,并分析了物料充满角对轴向位移速度的影响。
Then the mean distance and the mean time of material flow were calculated by means of filling method, the influence of the filling angle of particle on the axial transport velocity was analyzed.
并采用各点点位位移速度图对所建立的函数模型进行验证,同时对状态方程的建立及初始值的选取进行分析总结。
Finally, it validated established model with each point displacement velocity chart, analyzed and summarized the established of state equation and selection of initial value at the same time.
针对盒形件拉深成形时法兰变形区的变形进行了材料塑性流动的理论分析,提出了位移速度差诱发剪应力的观点。
In of displacement induces shear stress. Shear deformation this paper, flow law of material is theoretically analysed based on deformation of the flange deformed area in box drawing.
他发现了一些液滴存在某个速度,还有其他的液滴有速度和位移。
He found that some droplets had a certain velocity, and then others had a velocity plus some step.
实例计算表明,此方法大大提高了运行速度,且能够提高大坝位移的拟合和预测精度。
Calculation shows that the proposed method can increase the computation speed and raise the accuracy of fitting and forecasting dam displacement.
熔体和气体前沿的速度和位移均急速上升。
The velocity and displacement of gas front and melt front increase dramatically.
磨头座、滑动系统采用进口的双直线导轨、双滚珠丝杆传动,以达到运行速度平稳、消除移动间隙(位移)。
Grinding head on, sliding imports of dual-use system linear guide, two-ball screw drive, to achieve the smooth running speed to eliminate mobile space (displacement).
运用矢量法建立机构的位移矢量方程,推导出速度、加速度矢量方程。
Establish displacement vector equation of mechanism using vector method to infer the speed and the acceleration vector equation.
通过分析调宽机模块的运动特性,可获得板坯侧压的位移和速度边界条件。
The boundary condition of velocity and displacement was gained during slab side press, through analyzing sp die kinematics character.
进口松下电机伺服控制系统,提供精确位移及速度控制。
Servo motor control system Imported from Japan Panasonic, provide accurate displacement and speed control.
提出了一种实用的带送物料流位移和速度检测方法。
A practical measuring method of the displacement and velocity of the material flow is proposed.
通过结合离散相似法和冲量定理,推演出一个计算位移和速度的递推公式。
A recurrence formula for calculating the displacement and the velocity is derived by combining the theorem of impulse with the method of discretized similarity.
通过数值计算得到了平移断层上滑移位移、速度及摩擦力的分布规律。
The distribution of slip displacement, slip velocity and friction force on the strike slip fault were obtained by numerical simulation.
并根据系统的数学模型对铸浆机系统的位移、速度、压力运用SIMULINK进行动态仿真。
With the help of those established mathematical models, software SIMULINK simulates the dynamic performance of the system in displacement, speed and pressure regulation.
用矢量法导出了旋转驴头式抽油机悬点运动的位移、速度和加速成度的表达式。
With the help of the vector method, the general expressions for the displacement, velocity and acceleration of the polished nod on the swing horsehead pumping unit(SHPU)was introduced.
它有四个主要的机械位移,其速度可以调整,由液压压力与无级调速改变。
It has four mechanical shifts, and its speed could be adjusted by hydraulic pressure with stepless speed change.
提出了偏置式偏心圆凸轮机构从动件的行程、位移、速度、加速度的无量纲表达式,并对其进行分析。
The paper brings forward and analyzes the non-dimensional formulas of setover eccentric CAM from the aspects of the travel, displacement, speed and velocity of the moving parts.
在数控机床测控系统中,反馈位移和速度的检测元件通常易发生故障。
The speed and place of the feedback have been breakdown frequently while checking components are used in numerically-controlled machine .
对状态变量的观测,仅测量结构的前几个位移或速度。
The first few steps of displacements of the structure are measured.
因为位移有方向,所以速度也有方向。
Since displacement has direction, velocity also has direction.
同时,在许多实际应用中,希望通过对加速度的测量来估计速度及位移。
At the same time, many applications want to estimate velocity and displacement by the measurement of acceleration.
位移,初速度,末速度,加速度和时间。
Displacement, Initial velocity, Final velocity, Acceleration and Time.
要从加速度记录计算速度和位移曲线也不是一件轻而易举的事。
The calculation of these velocity and displacement curves from the accelerogram is not a trivial matter.
分析求解了在碰撞过程中汽车变形的位移、速度、加速度和碰撞力;
The displacement, speed, accelerated speed and collision force during collision are analysed and solved.
最后,本文就实现位置运动控制的位移、速度数字控制技术进行了探讨。
In the end, this dissertation introduced displacement and velocity computer control method for position motion control.
输入层分别为小车的位移和速度、摆杆偏离铅垂线的角度和角速度。
Input layer is respectively the displacement and speed of car, the Angle and Angle speed between pendulum bar and vertical line.
对四种非稳定工况下的动态特性进行计算机仿真,得出整个刮板输送机在任意点的位移、速度、加速度和动张力。
Finally, computer simulation is applied to get the displacement, velocity, acceleration and tension of the anyplace on the scraper conveyor for the four special working condition.
根据该振动筛的工作原理,得出了筛箱运动位移、速度和加速度等运动方程。
According to working principle of the linear shale shaker, the movement equations about displacement, velocity and acceleration are given.
应用推荐