传感器数据采集模块的控制与实现。
The control of data collection module for sensors and its achievement.
本文重点设计了一套多维力传感器数据采集的硬件系统。
The emphasis of this paper was laid on the design of the data acquisition system of multi-component wheel force transducer.
为此论文开展于无线传感器网络技术的温湿度传感器数据采集系统的研制工作。
To that end papers in wireless sensor network technology in the temperature and humidity data acquisition system of work.
介绍了一种基于TMS320F 2812DSP、仪表放大器的传感器数据采集系统的设计。
This paper introduces a kind of design based on TMS320F2812 DSP and IN-AMP in sensor data collection system.
下位机采用可编程控制器（PLC），用于实现运动控制、阀门等动作控制、定时和传感器数据采集。
The lower machine used PLC to realize motion control, action control such as valve control, timing and data acquisition from sensors.
它还能调取与室外设备相连的传感器收集的数据，这些信息通常依赖直升机或地面人员采集。
It could also retrieve data from sensors that are already connected to equipment in the field but which normally rely on helicopter or ground visits to get the information.
一个复合应用程序的传感器数据是从业务组件实例的传感器数据中采集来的。
The sensor data of a composite application is aggregated from sensor data of business component instances.
数据采集产品像聚焦点一样为系统服务，和一系列产品一起，诸如传感器显示温度、水流、程度或者过程。
Data acquisition products serve as a focal point in a system, tying together a wide variety of products, such as sensors that indicate temperature, flow, level, or pressure.
实践证明，该节点实现传感器数据的采集与无线传输，以及TEDS数据的定义与应用。
Practice shows that the node can realize the acquisition and wireless transmission of sensor data, and the definition and application of TEDS data.
传感器节点采集到的数据必须结合其位置信息才有意义，没有位置信息的数据几乎没有利用价值。
Raw sensor data must be combined with spatial information and the value of the raw data increases substantially. Raw data without its position information has less capability.
本课题阶段主要进行了粮食水分在线检测方法制定和传感器研究，数据采集控制和软件是下一步深入研究内容。
This paper only makes research on establishment of testing methods and sensor, and detailed research on data collection and control is to be continued on next stage.
有了TEDS，传感器就可以向与其连接的数据采集系统对自身进行自我识别和描述。
With TEDS, the sensor identifies and describes itself to the data acquisition system to which it is connected.
介绍了一种汽车方向盘转角传感器，搭建了汽车方向盘转角数据采集系统。
A steering wheel Angle sensor was introduced and a data acquisition system for steering wheel Angle was built.
以此为理论基础，组建了由传感器、数据采集卡、虚拟仪器软件以及计算机等组成的放电检测系统。
With which as the theory base, the discharge auto detecting system made of sensors, data acquisition card, virtual instrument software and computer was established.
针对IEEE1451.4标准定义的混和模式智能传感器模型，通过分析，建立智能数据采集节点模型。
According to the mixed smart sensor model in IEEE1451.4, based on the analysis, smart data collect note model is built.
系统组建简单方便，使用灵活可靠，为基于计算机和传感器的数据采集系统提供了一种简单而实用的实现方法。
The system is simple, useful, reliable and flexible. A simple and useful method for the data acquisition system based on computer and sensors is provided.
本设计完成的网络测试系统主要由传感器、信号调理、数据采集、网络接口、显示以及通用计算机硬件和软件等基本要素组成。
This network testing system is mainly made up of basic elements such as sensors, data acquisitions, network interface, display, universal computer software and hardware, etc.
因为多媒体数据的高带宽要求，要传输传感器节点采集到的原始数据将会消耗大量的资源。
Because of the high bandwidth demands of multimedia date, the transmission of raw data collected at sensor nodes will consume a large amount of resources.
实际应用证实所设计的传感器和数据采集系统使用方便且可靠性高。
Actu al application has proved that the transducers and the data collecting system are reliable and convenient for use.
建立了由电气比例阀、位移传感器、数据采集模块及计算机等组成的机械压力机智能控制系统。
A new intelligent control system primarily composed of electric proportional valve, displacement transducer, data acquisition and process module is constructed.
主要由流动注射分析系统、半导体恒温器、固定化酶反应柱、量热传感器、数据采集模块组成。
It consists of FIA system, semiconductor thermostat, immobilized enzyme reaction column, thermal sensor and data collection module.
利用基于DSP的运动、压力控制器对编码器和传感器采集的数据进行高速处理，实现了对压铸机的实时控制。
Using movement & pressure controller based on DSP to make high-speed disposal on the data collected by the coder and the sensor, the real control on the die-casting machine was realized.
传感器在各种数据采集与检测系统中起着至关重要的作用。
Sensor play an important part in data collecting and monitoring system.
该系统由水泵试验台、传感器、信号调理电路、数据采集卡、计算机处理几个部分组成。
This system consists of: pump test bed, sensors, signal processing circuit, data-collecting card, computer processing.
DAQ式虚拟仪器自动测试系统是由传感器、信号调理、数据采集硬件、通用计算机、软件等基本要素构成。
And this system is composed of some essential elements such as sensor, signal-modulating circuit, hardware of DAQ, general computer, relative software and so on.
本文的研究目的是设计一种基于石英谐振式力敏传感器的无线数据采集系统，用于大型建筑的钢结构受力检测。
The purpose of the research in this paper is to design a kind of wireless data collection system with quartz resonance force sensor, for the detection of the steel structure in large building.
整个系统由光纤电压传感器、数据采集卡及一台微机组成。
The system is made up of an optical voltage sensor, a high-speed data acquire board and a computer.
该纺织机械整机测试平台包括多传感器、多功能数据采集卡、计算机及虚拟仪器软件。
The spinning mechanism test flat roof includes multi-sensors, multi-functions data collection cards, computer, and the virtual instrument software.
由气象传感器、数据采集单元、数据预处理系统和中心服务器组成。
It makes up of meteorological sensor, data acquisition unit, pretreatment system and central server.
由气象传感器、数据采集单元、数据预处理系统和中心服务器组成。
It makes up of meteorological sensor, data acquisition unit, pretreatment system and central server.
应用推荐