存储40小时以上的仪表读数。
最惊人的例子之一出现在团队为仪表读数构建数据模型时。
One of the most striking examples arose as the team attempted to build a data model for meter readings.
机电仪表示一种电表，因为仪表读数在传感元件电阻中变化多样。
The electromechanical gauge ACTS as an ammeter because the gauge reading changes with variations in the sender unit resistance.
仪表的测量系统由接头、弹簧管和传动机构组成。通过指针指示仪表读数。
The system of measurement is composed by joint, spring pipe, and power transmission setting, and use the needle to note the number.
通过仪表读数及与之读数相对应的在测式中所用销酸银溶液的量建立一个图表。
Construct a graph by plotting the meter readings versus the volumes of standard silver nitrate solution used in the titration.
提出并分析了读数中值得商榷的一个问题，得出了关于分度式仪表读数的一般规则。
This paper analyzes a problem in digital reading, and then concludes the general rule in digital reading of division meters.
将阀门保持在这个位置，当安全阀出现可以看到的第一次排放的同时，观察仪表读数。
Hold the valve at this position and observe the reading at the moment the first discharge is noted from the relief valve.
CIM数据模型提供了两种不同的记录仪表读数的方法：reading和interval - reading。
The CIM data model offered two different ways to record meter readings: reading and interval-reading.
“如果使用标准的仪表读数定义，会为每个读数创建一个容器。如果每15分钟读取一次仪表，每天每个仪表就会有96个对象，”Herdt说。
"Using the standard meter reading definition, you would create a container for every reading, which computes to 96 objects per day per meter if you read a meter every 15 minutes," says Herdt.
当飞行时飞行员可以操纵的每一个系统或部件都要进行操纵，以确定量产飞机与原型机有着相同的性能；在飞行期间，仪表读数要在正常范围之内。
An operational check of each part or system operated by the crew while in flight to establish that, during flight, instrument readings are within normal range.
该机构（BEA）表示在同雷暴搏斗的过程中，飞机上各仪表上得出的航速读数不一致。
The agency, BEA, said the plane received inconsistent airspeed readings from different instruments as it struggled in a huge thunderstorm.
每个仪表每天将生成至少1,440个读数，每月30天，每年12个月。
Each meter will produce at least 1,440 readings per day, 30 days per month, 12 times per year.
如果每个月记录一次读数，那么没问题；但是对于智能仪表，团队设想应该几分钟测量一次，这意味着数据量会快速增长。
Not a problem if you're recording one reading per month, but with smart meters, the team envisioned reading at intervals measured in minutes, which meant data volumes would mount quickly.
三位宇航员躺在舱内，观察着各种仪表的读数。
The three astronauts lying in the cabin, watching the readings of various instruments.
仪表上的读数显示出引擎的温度异常地高。
The reading showed that the temperature of the engine is abnormally high.
接着，分析了采用低精度仪表自动判读方法对高精度仪表进行自动读数时，引入误差会增大高精度仪表的读数误差。
Secondly, the paper analyzes that importing error will increase reading error when the automatic recognition method of low-precision meters is used to recognize the reading of high-precision meters.
它由光栅-棱镜单色仪、探测器、读数仪表、标准灯组及微型计算机组成。
It consists of a grating-prism monochromator, detectors, readout electronics, standard lamps and a microcomputer.
我们应当先观察仪表，并根据所取的读数进行操作。
We should observe a meter and act according to the readings we take .
指针式仪表的自动读数是近年来的热门研究内容，但一直存在由成像畸变导致的误差较大的问题。
Automatic reading of analog meter has been a research hotspot recently, but the reading error caused by imaging distortion always exists.
针对直读式流量仪表检定问题，采用了摄像头代替人眼读数的方法，研制了直读式流量计的摄像检定系统。
Using the reading way that the camera replaces eyes in the test of flow meter with no signal, the testing system of shoot for flow meter with no signal is developed.
实验表明：该读数方法绝对误差为零，非常适合于高精度指针式仪表自动跟踪判读。
The experiment shows that the absolute error of the reading approach is zero, which is applicable to automatic tracking reading of high-precision meter very well.
常规的摩托车磁电机参数测量方法是用交流电流、电压表及示波器等仪表进行测量，再从表上进行读数并记录。
The normal parameter-measure method of motor magneto is using alternating current, voltmeter and instrument to measure then read and record the data.
介绍了一个数码管显示数字仪表表盘读数的自动识别系统。
An automatic recognition system for characters on numeric meter dial plate displayed by LED is introduced.
现在，对很多没有计算机操作界面的指针式仪表的检定通常都是由人工来读数和调节，然而，人的眼睛在大量的视觉工作之后会出现视觉疲劳，造成了检定精度低，检定周期长。
But, usually, detecting of the gauge with pointer is by manual work, after long time for vision work, eyes will get tired, and this leads to low detecting precision and long detecting period.
同时应用LCD显示器进行数字显示，读数方便准确，较大的提高了仪表的测量精度。
At the same time, it improves obviously the measure precision and the reading is convenient and right, using LCD.
我们应当先观察仪表，并根据显示的读数进行操作。
We should observe a meter and act according to the readings we take.
我们应当先观察仪表，并根据显示的读数进行操作。
We should observe a meter and act according to the readings we take.
应用推荐