修复机器人六个关节均选用交流伺服电机驱动。
The six joints of the repairing robot are all driven by AC servo motors.
本传动系统由交流伺服电机、滚珠丝杠及直线导轨等组成。
The drive system consists of AC servomotor, ball screw and rectilinear orbit etc.
研究了一种由交流伺服电机驱动的全自动高速平缝机控制器。
The automatic high-speed sewing machine controller is studied in this paper.
重点介绍了FPGA的基本组成原理及在交流伺服电机中的应用。
The FPGA principle and application on ac servo motors are introduced emphatically.
采用台达交流伺服电机及控制器实现精确定长剪切，全闭环控制。
DELTA AC servo motors and controllers to determine the precise length cut, closed loop control.
采用台达交流伺服电机及控制器实现精确定长剪切，全闭环控制。
DELTA AC servo motor and controller for precision to determine the long cut, full closed-loop control.
介绍了一种用于电脑全自动工业平缝机的永磁交流伺服电机及其控制系统。
Permanent ac servo motor control system of lockstitch sewing machine is introduced.
介绍了基于TMS320F2812交流伺服电机控制系统的整体方案设计。
The whole project design of the AC servo motor control system based on TMS320F2812 is introduced.
针对以交流伺服电机驱动的二自由度并联机器人，设计了智能模糊滑模控制算法。
An intelligent fuzzy sliding mode control for 2-dof parallel robot which derived by AC servo motor was designed.
机床的进给系统通常是通过交流伺服电机驱动的驱动滚珠丝杠饲料，简化结构，实现。
Machine tool feed system is usually driven by ac servo motor ball screw feed drive to achieve, to simplify the structure.
针对三个不同的运动阶段，建立了包含交流伺服电机速度环的被控系统的完整的数学模型。
Considering the three different moving processes, complete mathematic model of controlled system that includes velocity loop of alternating current servomotor, is established.
介绍交流伺服电机控制系统的组成、主要特性、控制原理及在系统调试过程中应注意的事项。
The article introduced the composition, the main characteristics and the control principle of the ac servo motor control system as well as points for attention in the system debugging process.
由于交流伺服电机内是无刷结构，几乎不需维修，体积相对较小，有利于转速和功率的提高。
Due to the ac servo motor is in brushless structure, almost does not need to repair, the volume is relatively small, be helpful for the improvement of speed and power.
介绍自行研制的基于80C196KC单片机的交流伺服电机控制卡的硬件设计及其软件实现。
The paper introduces the hardware and software design of an AC servo motor control card based on 80C196KC.
文中重点叙述了MPC02运动控制卡、松下交流伺服电机和驱动器及工控机组成的硬件系统。
The hardware system that composed by MPC02 card, Panasonic AC servo motors and their drivers was mainly discussed.
采用进口高品质交流伺服电机、滚珠丝杠、线性滑轨及电气配件以确保设备具有较高的加工精度；
The use of imported high-quality AC servo motors, ball screws, linear rails and electrical accessories to ensure that the equipment has a high processing accuracy;
常用的伺服电机是交流伺服电机，在电机的轴端装有光电编码器，通过检测转子角度用以变频控制。
Commonly used servo motor is ac servo motor, the motor shaft with in the photoelectric encoder, by detecting the rotor Angle to frequency conversion control.
提出了机械传动部件和大功率交流伺服电机的设计方法，并实际应用于1000kN数控折弯机中。
The design method about machine drive component and high - power ac motor is discussed. A engineering application case of 1000kn CNC brake - press is given.
介绍了一种由at89c 51单片机控制交流伺服电机的系统方案，包括系统硬件设计和软件设计。
The paper provides a scheme to control AC servo-motor using single chip-computer AT89C51, including hardware design and software design.
目前常用的伺服电机是交流伺服电机，在电机的轴端装有光电编码器，通过检测转子角度用以变频控制。
Now commonly used servo motor is ac servo motor, the axial end in motor with photoelectric encoder, by examining the rotor Angle to frequency conversion control.
文中重点叙述了PMAC可编程多轴运动控制器、松下交流伺服电机和驱动器及工控机组成的硬件系统。
This thesis gives great emphases on the hardware system consisted of PMAC, Panasonic AC servo-motors, drivers and IPC.
采用交流伺服电机作为驱动器件，可以和直流伺服电机一样构成高精度，高性能的半闭环或闭环控制系统。
Adopting ac servo motor as the driving device, can the dc servo motor and a high precision, high performance as the half closed loop or closed loop control system.
采用交流伺服电机作为驱动器件，可以和直流伺服电机一样构成高精度，高性能的半闭环或闭环控制系统。
Adopting ac servo motor as a drive device, can and dc servo motor as a high precision, high performance and a half closed loop or closed loop control system.
同时采用交流伺服电机作为驱动元件，基于MPC02运动控制卡作为上位控制单元构建了开放式控制系统。
In the meantime, by using an AC servo motor as the driving parts and based on the MPC02 motion control card, the open control system was formed.
通过变频器、交流伺服电机、行程光电编码器等设备组成了行程控制系统，实现了可移动台架位置的精确控制。
Travelling control system is composed of a transducer, an AC servo motor, an optical encoder and other components, which achieves precise control of the movable bench's position.
采用交流伺服电机和机械驱动进给系统的冷轧环机，其进给伺服控制系统的设计需要一个新的工艺动力学模型。
The feed drive system of a precision cold ring rolling mill adopts AC servo motor and mechanical transmission, rather than conventional electro-hydraulic actuator.
介绍在刚性连接方式下，用两台交流伺服电机同时驱动同一负载方案的组成、硬件和软件，给出了该系统的实验结果。
Introduce the composition, the hardware and software for two AC servo motors which drive loads simultaneously under rigid connection. Also Present the experimental results.
进给传动：三向进给均采用交流伺服电机驱动精密滚珠丝杆，专用丝杆轴承支承，提高了机床的进给运动刚性和精度。
Feed transmission: using AC servo motor to drive the precise ball screw sets that supported by special ball screw bearing, which improves the rigidity and precision of feed movement.
SANO三相智能型伺服变压器是专门针对中国电网与交流伺服电机所需电压不匹配而设计的超小体积三相伺服变压器。
SANO intelligent servo transformer is a super-small size servo transformer, specifically developed for the non-compatibility voltage between the China Electrical and the alternating servo motor.
SANO三相智能型伺服变压器是专门针对中国电网与交流伺服电机所需电压不匹配而设计的超小体积三相伺服变压器。
SANO intelligent servo transformer is a super-small size servo transformer, specifically developed for the non-compatibility voltage between the China Electrical and the alternating servo motor.
应用推荐