目的：建立X线头颅侧位定位片硬组织形态二维有限元分析模型。
Objeclive:To establish a two dimensional finite element analysis model for hard tissue morphology on lateral cephalometric X ray film.
目的探讨一种与多普勒超声相结合的人体二尖瓣狭窄下游湍流剪应力二维有限元分析方法。
Objective:To conduct such a study on TSS downstream of mitral stenosis using a finite element model of two dimensions combined with Doppler echocardiography in human beings.
不确定性参数的二维热结构有限元分析研究有着广泛的工程背景和重要的理论意义与学术价值。
The research about finite element analysis for two-dimensional thermal structures with uncertain parameters has extensive engineering-background, important theory meaning and academic value.
采用二维平面模型，“以静代动”的荷载简化方法，建立沥青路面永久变形有限元分析模型。
The two-dimension plane model and the simplification of dynamic loading are applied to create the finite element model for asphalt pavement permanent deformation analysis.
用TL法分析研究，建立了二维弹性大变形接触问题的一般实用有限元分析模型。
A general practical finite element analysis model for two-dimentional elastic large deformation contact problems was established using the TL method.
本文介绍二维分岔槽道内非牛顿流体流动的有限元分析。
This paper presents finite element analysis of non-Newtonian fluid flow in 2-D branching channel.
本文介绍了二滩水电站工程导流隧洞右岸0+679剖面二维非线性有限元分析结果。
The two-dimensional nonlinear FEM results for Ertan project were introduced in this paper, which were analysed on the section 0+679m of the diversion tunnel on the right bank.
采用二维非线性有限元分析方法，研究了六库水电站RCC纵向围堰防渗墙的防渗效果和应力应变状态。
The stress state and seepage of anti-seepage walls under longitudinal RCC coffer dam of Linkuhydropower station are studied using 2d non-linear finite element method.
针对传感器弹性体的重要性，本文应用有限元分析软件ANSYS对二维轴承载荷传感器弹性体进行了结构优化设计。
Aiming at the importance of the elastomer, based on the ANSYS, the thesis has realized the structure optimization design of the elastomer of two-dimensional bearing load cell.
开发了通用的分析二维金属成形过程的有限元分析软件s—FORGE。
A general computer code, called S-FORGE, is developed for analyzing 2d metal forming process.
然后，在对三维有限元分析结果研究的基础上，建立了环缝处的纵向螺栓剪切模型，利用该模型可以计算得到错缝拼装衬砌二维梁-弹簧模型中环间剪切弹簧的刚度；
Based on the 3D analysis result, shear models of ring joint bolt is built and shear parameters between rings needed in 2D analysis with beam-spring model can be obtained by this shear model.
采用有限元分析软件ANSYS建立了BLDCM的二维和三维定子振动的有限元分析模型，研究了BLDCM定子结构和参数对其振动模态和固有频率的影响。
This paper constructs several 2d and 3d finite element analysis models with ANSYS, studies the influence of the structure and parameters of BLDCM on vibration mode and natural frequency.
采用有限元分析软件ANSYS建立了BLDCM的二维和三维定子振动的有限元分析模型，研究了BLDCM定子结构和参数对其振动模态和固有频率的影响。
This paper constructs several 2d and 3d finite element analysis models with ANSYS, studies the influence of the structure and parameters of BLDCM on vibration mode and natural frequency.
应用推荐