清单9展示了主程序循环的开始部分。
清单4显示了主程序循环中的三指检测的开始部分。
Listing 4 shows the beginning of the three-finger detection in the main program loop.
第2部分把scoresortresults子例程注入到主程序逻辑中来给每条匹配的记录评分、给结果列表排序并将其传递给显示步骤。
Part 2 injects the scoreSortResults subroutine into the main program logic to score each matched record, sort the resulting list, and pass it on to the display step.
清单6和7展示了主程序逻辑的其余部分以及shakecheck子例程，它将捕捉动作并切换模式。
Listings 6 and 7 show the remainder of the main program logic and the shakeCheck subroutine that perform the gesture acquisition and mode change.
要完成修改，请将my %jobMP = (); my %nameMP = ();添加到变量声明部分中并将主程序逻辑从清单14修改为清单15。
To complete the modifications, add my %jobMP = (); my %nameMP = (); to the variable declaration section and modify the main program logic from Listing 14 to Listing 15.
本文阐述了调试器系统的电路组成和工作原理，介绍了调试器系统的主程序流程，并详细地介绍了各组成部分的功能。
This paper expounds circuit form and work principle and main program flow of the debugger system, and detailedly introduces function of each composing part.
在软件方面，介绍了主程序的流程图及各部分电路的编程方法。
In the software aspect, it curtly introduces flow chart of main program and the programming method of all ports of circuit.
软件设计部分给出了主程序和子程序的流程图及软件设计思路。
Flow chart and design thought of main and subprogram is presented in software design part.
介绍了控制方案和程序流程图及部分主程序。
Control plan, procedure flowchart and part of main procedure are introduced.
软件部分采用模块化设计方法，主要有主程序、键盘管理、液晶显示、中断服务、测量控制及结果处理等几个模块。
The software, which employs modularization method, includes modules such as main programs, keyboard management, LCD, break service, measurement control and results treatment etc.
系统软件部分运用C语言编制单片机程序，主要包括主程序、动态扫描显示子程序和按键扫描子程序等。
System software part of the preparation of the use of C language SCM process, including the main program, dynamic scanning display routines and key scan subroutine and so on.
系统包括上位机软件、RS232—485转换器、分机模块及电缆连接4部分，其监控程序的设计采用顺序查询的方式执行主程序。
The system consists of upper computer software, RS232-485 converter, every kind of modules and cables. And finally the monitor program is designed with the sequential query mode.
洋细论述了系统的总体结构、部分硬件设计和相应固件程序的实现，给出了主程序和中断服务程序流程图。
Then, the whole systematic architecture, some hardwares and firmware program were detailed, finally, the main program and interrupt service program were provided.
结合S7—200系列plc的特点，制定了通信规约，画出了PLC的主程序流程图，并给出了部分调试结果。
The communicate stipulations of an agreement is constituted according as the characteristic of S7-200 PLC. The main procedure flow chat is drawn. The part of debugging result is shown.
因为附属程序集不是主程序集的一部分，所以您不必替换该应用程序的主程序集，即可很容易地替换或更新与特定区域性相关的资源。
Because the satellite assemblies are not part of the main assembly, you can easily replace or update resources corresponding to a specific culture without replacing the application's main assembly.
软件部分着重论述了主程序设计、对MFRC500的应用程序设计以及读卡器外围功能程序设计。
The software aspect is emphasis on the plan of the main program, the design of MF RC500 application and the realization of the function of the reader's outer operation.
框架由主程序、接口和插件三个部分有机的结合而成，具有良好扩展性、通用性和安全性。
It was made up by main application, interfaces and plug-ins. And it has of good scalability, versatility and security.
软件动态过程采用前后台结构，包括主程序和中断服务程序两部分。
Dynamic process of soft adopts front ground and back ground structure, including main program and interrupt service program.
本文第三部分将举证责任转移规律在民事案件中的运行做了程序化设计，将其分为审前程序和主程序两个部分。
In the third part the procedure run in civil cases will be designed, it has two parts:pre-hearing procedure and main procedure.
控制系统软件设计主要包括主程序、冷却水参数检测子程序、激光功率控制子程序与人机界面子程序等四部分的程序设计。
The control system software contains the main program, the cooling water parameters detection subprogram, the laser power control subprogram, and the human machine interface subprogram.
硬件结构由微处理器和串口控制器两部分组成，程序分为主程序和中断子程序两部分。
It is composed of the microprocessor system and a serial port controller. The software is divided into main program and interruption program.
文中给出了机械改进示意图，PLC的电气硬件图，主程序框图及部分子程序。
The sketch map of mechanical improvement, the electrical hardware plan of PLC, the frame of main program and partly subprogram are showed in the pap...
文中给出了机械改进示意图，PLC的电气硬件图，主程序框图及部分子程序。
The sketch map of mechanical improvement, the electrical hardware plan of PLC, the frame of main program and partly subprogram are showed in the pap...
应用推荐