摩擦片的温度变化对主离合器的性能影响很大。
The variations of plate temperature affects the performance of main clutch.
表面非均匀磨损是重载车辆主离合器分离环常见的失效形式。
The nonuniform wear is a popular failure mode of separating ring of heavy vehicle clutch.
主离合器通过行走轮驱动轴连接、主离合器操纵杆连接至插植机构。
A main clutch is connected through the driving axle of the walking wheel, and the operating rod of the main clutch is connected to the planting device.
经主离合器操纵杆及行进离合器操纵杆控制将动力传动至行走轮驱机构和插植箱驱动轴。
The power is delivered to the walking wheel driving device and the planting case driving axle through the controlling of the main clutch operating rod and a walking clutch.
要反复调整反复试验，直到确认达到最满意，首先，将传动轴安装上，将主离合器拉杆连接上。
Repeated trial and error to adjust until the confirmation to achieve the most satisfaction First, install the drive shaft, Will connect the main clutch lever.
采用数值仿真和优化方法，对主离合器接合过程进行了分析研究，提出了最佳接合过程的压紧规律。
The engagement process of the main clutch is analyzed using digital simulation and optimization and a compressing rule of optimal engagement process is presented.
转向离合器同主离合器一样，是履带式工程机械的易磨损部件，应进行热负荷计算，以保证其有足够的热容量和使用寿命。
As the main clutch, the steering clutch is an wear part in track type construction machines. It should pass through thermal load calculation to ensure adequate thermal capacity and service life.
在AMT技术中，最为困难的是离合器（主离合器）控制， 离合器控制技术已经成为实现机械传动变速自动操纵的关键技术。
The most complex part in ASCS is clutch control, which, in the mean while, is the key technology of realizing automatic control of AMT of vehicles.
分析了主离合器摩擦片的磨损具有沿径向非均分布的特点，指出摩擦片在使用过程中，局部高温和材料软化是产生磨损的重要原因。
The wear of friction wafers in main clutch features uneven radical distribution. In the operation of friction wafers, high local temperature and material softening are important reasons causing wear.
结合当前工程机械维修工作的实际情况，对主离合器、液力变矩器、驱动桥、转向离合器和转向制动器等部位的故障现象进行了深入的探讨。
Based on the practical situations of current construction equipment maintenance, the fault of master clutch, hydraulic torque converter, driving bridge, steering clutch and brake are discussed.
径向贴装制动器卡钳和主缸是一种给予，是一个精致版的拖鞋离合器。
Radial-mount brake calipers and master cylinder are a given, as is a refined version of its slipper clutch.
主绞车（40级和50级 ）采用气胎离合器换档，适合远距离操作，方便快捷。
The main drawworks (40 and 50 model) utilize air-tube clutch to shift gears, which are suitable for remote control, fast and convenient maintenance.
摩托车离合器、单相器、起动电机、主付轴、主付轴总成、齿轮、离合器、离合片、单碳刷、碳刷总成、超越启动珠、套缸。
Motorcycle clutch, single phase, starting motor, main shaft, main shaft assembly, gear, clutch, clutch plates, single carbon brush and carbon brush assembly, beyond the startup beads, set of cylinder.
摩托车离合器、单相器、起动电机、主付轴、主付轴总成、齿轮、离合器、离合片、单碳刷、碳刷总成、超越启动珠、套缸。
Motorcycle clutch, single phase, starting motor, main shaft, main shaft assembly, gear, clutch, clutch plates, single carbon brush and carbon brush assembly, beyond the startup beads, set of cylinder.
应用推荐