它由多丝室、延迟线、主放大器、定时单道以及时幅变换器等组成。
It consists of a multiwire proportional chamber, a delay line, a main amplifier, a timing single channel amplitude analyser and a time to amplitude converter.
主放大器采用开关电容共模反馈电路在获得大输出摆幅的同时降低了功耗。
Used the switched capacitor Common Mode Feedback circuit(CMFB) in main amplifier to achieve a large output voltage swing and decrease the static power consumption at the same time.
光接收机前端放大电路主要由两个关键电路构成：前置放大器和主放大器。
The front-end amplifier for optical receiver is made up of two important circuits: preamplifier and main amplifier.
补偿放大器是由一个主放大器和一个辅助放大器组成，辅助放大器消除了主放大器自身的失调漂移。
The compensation amplifier consists of main amplifier and an auxiliary one. The auxiliary amplifier reduces input offset drift on output of the main one.
设计了与CMOS工艺兼容的光电单片接收机电路，其中包括光电探测器、前置放大器和主放大器。
Circuits of CMOS-process-compatible monolithic photoreceivers are designed. The circuits include photodetector, pre-amplifier and main amplifier.
在用于光纤传输系统的几个功能电路中，构成光接收机前端放大电路的前置放大器和主放大器是两个关键电路。
In the building blocks of an optical transmission system, the pre-amplifier and the main amplifier are the critical parts.
由于限幅放大器具有设计简单、功耗低、芯片面积小和外接元件少的优点，本文选择限幅放大器的形式来实现光接收机的主放大器。
The latter one was chosen to realize the main amplifier in our design since it has the features of simple topology, few external components and fast responsibility.
列读出级采用新型主从两级放大列读出结构，其中主放大器完成电荷到电压的转换，从放大器驱动输出总线来满足一定的读出速度。
In the design of column readout stage, master and slaver structure has been adapted, where master amplifier converts charge to voltage, and slave amplifier works with standby mode to drive output bus.
列读出级采用新型主从两级放大列读出结构，其中主放大器完成电荷到电压的转换，从放大器驱动输出总线来满足一定的读出速度。
In the design of column readout stage, master and slaver structure has been adapted, where master amplifier converts charge to voltage, and slave amplifier works wit.
读和写操作是通过两条公共的数据总线进行的：其中一条联结32个奇数列，另一条联结32个偶数列，用一个公用的主放大器把数据输出。
Read and write-operations are carried out by two common data buses: one is connected with the 32 odd rows, the other is for the 32 even rows. The data output is executed by a common main amplifier.
此限幅放大器由输入缓冲、主放大单元、输出缓冲、偏置补偿电路四部分组成。
This limiting amplifier composed of an input buffer, amplifier cells, output cells, and offset cancellation circuit.
在硬件设计方面，完成了阅读器主电路及功能模块的设计，特别是对D类功率放大器、编码器和电感线圈的设计理论和方法作了详细介绍。
In the design of hardware, the paper details in introducing the reader circuit and function module, especially the theory and method of design in D-type power amplifier, Manchester code and coil.
本工作试制成功了用于测量主传动系统静、动态速降的比较放大器，它具有较高的灵敏度与响应速度。
An amplifier which is used to measure the static and dynamic speed droop has been developed successfully, it gives out higher sensitivity and responsibility.
运放参数主测试电路采用辅助放大器测试法设计，通过相位补偿网络消除电路自激现象。
The main test circuit adopts the auxiliary amplifier method with phase compensation circuits in order to avoid self-excitation.
结合双包层掺镱光纤(YDCF)和主振荡功率放大(MOPA)技术，利用熔融拉锥的光纤侧面耦合器，设计和实验研究了全光纤结构的脉冲光纤放大器。
Using the side-pumped coupler made from fused tapered fiber, the Yb-doped double-cladding fiber (YDCF) master oscillation power amplification (MOPA) with all-fiber structure is experimentally studied.
结合双包层掺镱光纤(YDCF)和主振荡功率放大(MOPA)技术，利用熔融拉锥的光纤侧面耦合器，设计和实验研究了全光纤结构的脉冲光纤放大器。
Using the side-pumped coupler made from fused tapered fiber, the Yb-doped double-cladding fiber (YDCF) master oscillation power amplification (MOPA) with all-fiber structure is experimentally studied.
应用推荐