主控制机模块的设计与实现。
研制出以单片机和可编程序控制器为主的主控机。
Develops by the monolithic integrated circuit and the programmable controller primarily master control machine.
介绍力-位置型力感觉系统的基本工作原理，阐述以8031单片机为主控制器的系统构成。
The basic operational principle of the force-position type sensing system is introduced and the composition of the system with 8031 single chip computer as the main controller is described.
以MCU作为主控单元，设计了全自动织领机控制器，介绍了其硬件结构、软件功能。
MCU based collar machine controller is introduced in this article, including its hardware structure, software functions and the implementation.
本文介绍了一个采用个人电脑（PC）作为工业控制系统的主控机来控制大型锻压机床的成功例子。
This article introduces an available control system for the huge hydraulic press machine tool by means of a personal computer (PC) as the main controller.
采用MCS-51单片机为主控制器，用于步进式冷床同轴的直流调速系统，比较成功地解决了强力矩耦合情况下的双机转矩平衡问题。
MCS - 51 computer on slice is used as the main CPU in the step DC governor system for cold bed solving problems of two unit torque equilibrium under heavy moment coupling.
针对传统无线通信是单向传输的局限问题，设计了基于nRF 905射频芯片的双向通信系统并以单片机为主控制单元。
Based on the traditional wireless communications limited transmissions is limited, based on the NRF905 rf chip design of two-way communication system and MCU control unit mainly.
本地主控机通过RS485总线向现场信号采集设备发送控制指令并接收采集的测试数据，从而实现对rs485总线通信的控制。
The local controller sends steering order to field signal-acquisition equipments and receives test data from RS485 bus, thereby communication control of RS485 bus was realized.
利用光缆传输系统实现变电站主控制室的上位机与现场的测量系统之间的通讯以提高系统整体抗干扰能力和信号传输的可靠性。
Optical cable is applied to communicate between measurement system near transformers and upper computer in main controlling room in order to improve reliability of monitoring system itself.
其中硬件电路包括键控制模块、显示模块、输入信号整形模块以及单片机和CPLD主控模块。
Hardware circuit includes key control module, display module, plastic module of input signal, single chip computer control module and CPLD main control module.
针对不间断供电的需求，介绍了一种以m 68hc 908sr12单片机为主控芯片的双电源转换控制器的研制方案。
To satisfy demand for uninterrupted power supply, the developing scheme of double power switch controller taking M68HC908SR12 controller as main control chip was introduced.
主控机通过I/O控制等离子焊机，采用RS232与机器人控制器通讯。
Main controller adopted RS232 to communicate with robot controller through I/O regulate plasma quenching welder.
设计了巡检机器人有限状态机模型，实现了机器人遥控与局部自主控制的有机结合。
A finite state machine model is developed for the robot to integrate remote-control and local autonomous control.
单片机通过CAN总线向主控制器发送检测数据，主控制器经过判断可主动启动并完成车体的制动动作。
The microcontrollers transmit data to the main controller by the CAN bus, the main controller can start-up and finish the brake action initiatively after estimating.
该系统基于80C31单片机为主控制器，采用了混合式稀土永磁步进电机为执行部件，并以双通道旋转变压器为天线位置传感器。
The system adopts 80C31 MCU as the main controller, hybrid Rare-Earth permanent magnet stepper motor as the execution component, bio-passage rotary transformer as antenna position sensor.
该系统采用了“绿冲突”和备用方案的容错控制方式。即使主控部件出现故障，信号机仍可以按备选方案工作。
Green signal conflict control and reserve plan control, are adopted in the system so that the signal control machine can still run normally even if the main controller fails to work.
在详细分析偏航控制系统控制要求的基础上，采用单片机89c51作为主控单元，设计了风电机组的偏航控制系统。
On the basis of analyzing the control process completely, the thesis designs yaw control system for WTGs using 89c51 single-chip computer as a main control unit.
利用PC机作为主控计算机，采用RS485网络系统对生产中的配料系统进行多点数据采集，并对整个配料生产过程进行监控和控制。
This paper describes a multipoint data sampling system for the manufacturing material-mixing system, which uses RS485 network system and PC as a master control computer.
冷辗机控制系统以工业PC为主控制器，通过相应的功能模块实现对冷辗进程的实时监控。
Industrial PC is the master processor of the cold rolling machine. The process of cold rolling monitored by the corresponding functional component real-timely.
由于控制器的控制算法比较简单，主控制器采用ATMEL公司的8位单片机AT89S52。
The main controller is an 8 bits Single Chip Microcomputer:AT89S52 produced by ATMEL company.
研究利用PIC 16c54单片机作为主控制器的低成本家用空调电话远程控制系统。
This article is about a low-cost telephone remote control system of the domestic air-conditioner based on PIC16C54 MCU.
主控制器使用单片机对各个传感器的信号进行采集、分析、计算，并进行补偿，得到所需数据，再将各种数据送到液晶显示器显示。
The master controller uses a single-chip computer to collect, analyze, compute and compensate the signals of all sensors, and gets the needed data, then displays all data via the LCD.
本文介绍一种以8098单片机为主控制器的数字PID控制系统。
A numerical PID control system which USES 8098 single chip microcomputer as its main controller is introduced in this paper.
底层主控制器与上位机之间采用以太网进行通信，实现了对系统的远程控制。
Ethernet communication is used for communication between the host computer and bottom controller to implement remote control of the system.
系统中采用了AT 89 C 2051型单片机作为主控制器。
The system utilizes AT89C2051 microcomputer as major controller.
介绍以omron C2 0 0 H可编程控制器为主控机，配有上位计算机的啤酒糖化工艺计算机控制系统。
A computer control system for beer saccharification process is introduced which is equiped with a superior computer and takes an OMRON C200H as its programmable controller.
采用西门子s7- 200PLC为主控制器，配以人机界面TD 400c和通信模块EM277，设计了某除湿机控制系统。
This paper USES S7-200 PLC as main controller to design a dehumidifier control system, which is equipped with HMI TD400C and communication module EM277.
然后经过一级可变增益放大器，在经过A/D变换，通过单片机串口将数字数据传输到ARM主控制板内进行处理。
Then after a variable gain amplifier, After A / D conversion and through the microcontroller serial digital data to the ARM within the main control panel for processing.
介绍了一种检测细长钢管内径的光电检测装置。该装置利用线阵CCD作传感器，采用8031单片机作为主控制。
In this paper, a photoelectric instrument for measuring inner diameter of steel pipe is introduced, in which the linear CCD is used as sensor, and 8031 monolithic computer as master control system.
提出了采用单片机at89c 51作为中央主控器，对光谱仪进行控制和信号检测的新系统。
A new system using single chip computer AT89C51 as the central controller for controlling and detecting of signal of the spectrometer is put forward in the paper.
应用推荐