向主程序注册序号、中断属性和线程属性。
Register the sequence number, interrupt nature, and thread attributes to the main program.
软件部分采用模块化设计方法，主要有主程序、键盘管理、液晶显示、中断服务、测量控制及结果处理等几个模块。
The software, which employs modularization method, includes modules such as main programs, keyboard management, LCD, break service, measurement control and results treatment etc.
X9241采用二线串行i2c总线与单片机传递数据。其软件由主程序、中断子程序组成。
Data between X9241 and SCM is transmitted with I2C Bus, and the software includes main program and interrupt subprogram.
在硬件设计的基础上，文中对系统软件设计中的检测主程序、A/D转换子程序、定时器A中断子程序和液晶显示子程序的设计进行了系统性介绍。
On the base of the hardware design, this paper introduces the main program, A/D convert subprogram, Timer A abruption subprogram and liquid crystal display subprogram of software systematic.
在本课题中按照控制电路的功能模块分别编制了采样、计算、显示、中断等函数，而在主程序中分别调用这些函数来实现相应功能。
To meet the control circuit's requirement, the function of sampling, calculating, displaying and interrupting is written separately and is called in main programme.
全面介绍了采用模块化设计方法所设计的系统主程序及设定、预压、通电、中断、模糊控制、熔核尺寸预测子程序等系统软件。
The soft-wares of system main program adopting modularization designing method and subprogram of setting, prepressing, electrifying, interrupting and fuzzy control are generally introduced.
设计了主程序模块、采样中断模块、故障处理模块，并分别编制了子程序。
The software is divided into main program module, interrupt module, fault disposal module. These subroutines of each module are designed respectively.
分析了系统软件的功能，采用模块化软件设计方法，设计了控制系统主程序、中断服务程序以及子程序。
After analysis the function of system software, main program, interrupt service program and subroutine were designed use modeling develop ways.
软件分为五块：主程序中的初始化模块、换相子程序模块、电流调节、速度调节子程序模块，定时器中断程序模块。
The system software involves five main modules: initialization module, phase-changing module, current-regulating module, speed-regulating module and timer interrupt module.
洋细论述了系统的总体结构、部分硬件设计和相应固件程序的实现，给出了主程序和中断服务程序流程图。
Then, the whole systematic architecture, some hardwares and firmware program were detailed, finally, the main program and interrupt service program were provided.
软件设计主要包括主程序、PWM中断程序、电流PI调节程序、速度MRAC调节程序。
The software programs include main program, PWM interrupt program, PI control program of current and MRAC control program of speed.
软件设计分为两块，主程序和中断子程序。
Software design is divided into two parts, the main program and interrupt service routine.
软件动态过程采用前后台结构，包括主程序和中断服务程序两部分。
Dynamic process of soft adopts front ground and back ground structure, including main program and interrupt service program.
整个电路采用模块化设计，由主程序、中断程序、发射子程序、接收子程序、显示子程序等模块组成。
The whole circuit USES modular design, by the main program, interruption program, launch subroutines, receiving subroutines, display subroutines etc module.
最后提出了整体系统的具体设计方案，给出了系统硬件框图，主程序流程及DSP中断程序流程。
At last, the thesis explicates the scheme of whole system and presents the system hardware frame diagram, main flowchart and DSP break-off flowchart.
并介绍了软件主程序和主要的中断程序。
This paper describes the software main program circle and the major interrupt program.
系统软件包括主程序，市电过零中断服务程序和多种子程序构成，采用模块化方法设计。
The system softwares include main program, voltage zero interrupt program and other sub-program, The system is designed with the model block.
硬件结构由微处理器和串口控制器两部分组成，程序分为主程序和中断子程序两部分。
It is composed of the microprocessor system and a serial port controller. The software is divided into main program and interruption program.
给出了四汉字显示模块的硬件电路原理图、主程序流程图以及中断显示流程图。
The basic circuit diagram, the main program flow chart and the display interrupt flow chart of four Chinese characterses display module are also given.
中断处理程序经常负责更新一些在主程序中被查询的变量的值。
Interrupt service routines often set variables that are tested in main line code.
控制程序设计包括定时中断服务程序、外中断服务程序及主程序。
The control program includes timing interrupt service program, external interrupt service program and main program.
系统软件主要由主程序和中断服务程序组成。
The system software includes the main program and interrupt service program.
根据热丝tig焊的时序要求，设计了控制系统的软件，重点介绍了主程序和中断服务程序。
The software for control system was designed according to the timing requirement, the main program and the interrupt service program were highlighted.
根据热丝tig焊的时序要求，设计了控制系统的软件，重点介绍了主程序和中断服务程序。
The software for control system was designed according to the timing requirement, the main program and the interrupt service program were highlighted.
应用推荐