应用该设计程序，设计出一系列内、外中心齿轮。
Serial internal gears and external gears are designed with this project approach.
中心轴上的齿轮的旋转驱动其他齿轮旋转得快些还是慢些，这取决于中心齿轮的齿数。
The rotation of this gear on a hub of shaft drives other gears which may rotate faster or slower, depending upon the number of teeth on the basic wheels.
机身为槽钢机架，主机配有低中心齿轮减速机，具有传动平稳，扭矩大，维修方便之优点。
The machine body is U-steel frame, and the main machine is collocated with low-center gear decelerator, with advantages of stable transmission, large torque, and convenient repair.
全新的动力装置以齿轮传动结构为特点，此结构允许前端风扇转速比中心部分慢3倍，优化了发动机各部分的速度。
The all-new powerplant features a geared architecture allowing the front fan to spin three times slower than the core, thus optimising the speed of each section of the engine.
这种齿轮传动的缺陷在于，每隔齿轮的中心到啮合点的距离在运转的过程中是变化的。
The problem with this type of gear is that the distance from the center of each gear to the point of contact changes as the gears rotate.
介绍了虚拟齿轮测量中心运动建模的体系结构。
The motion modeling system structure of virtual gear measuring center is introduced.
在水上运动中心将为你提供的浮浅齿轮和浮选背心，如果你想的话。
The water sports centre will provide you with snorkelling gear and a floatation vest if you would like one.
进入变速箱，万向节连接中心传动轴到内部锥齿轮。
Going into the gearbox, universal joints connect the centre drive shaft to the internal bevel gears.
同时结合齿轮测量中心的测量方式和环面蜗杆的特点，确定了对环面蜗杆误差项目的测量方法，并分析了测量时的运动控制策略。
At the same time, combine with the measure method of gear measuring center and the character of hourglass worm the method of error measurement is fixed.
船舶在波浪中航行时，船体总弯曲变形会使沿船体纵向布置齿轮机构的轴承支座中心距产生缩减。
When sailing in waves, ship hull total bending deformation will reduce the center distance of gear backing radially arranged in ship hull.
齿轮泵的磨损部位主要有主动轴与衬套、被动齿轮中心孔与轴销、泵壳内腔与齿轮、齿轮端面与泵盖等。
Pump wear parts are mainly drive shaft and bushing, passive gear center hole and shaft pin, pump shell lumen and gear, gear face and pump cover, etc.
在一定条件下，这种中心距缩减会导致互相啮合的两齿轮间产生附加径向压力。
Under certain conditions, this reduction of the center distance will lead to additional radial pressures between two meshing gears in the gearing.
合理的节曲线设计是可用于低速大扭矩液压马达的变中心距非圆行星齿轮机构正常工作的关键。
Appropriate pitch curve designing is a key of regularly working for non-circular planetary gear mechanism with variable center distance which can be used in low speed high torque hydraulic motor.
研究了定中心距、定啮合角变速比齿轮的啮合原理。
The conjugate principle of the variable ratio gear with constant center distance and constant contact Angle has been analysed.
振动力完全平衡后机构的振动力矩，可通过调整附加机构中偏心齿轮的回转中心得到部分平衡。
The shocking moment after the complete balance of shocking force can get partial balance through the adjustment of eccentric gear in the attached mechanism.
确定了非圆齿轮的基本参数：基础圆半径、偏心率、变形距和中心距比例系数。
The basic parameters of non-circular gear are determined, such as primary circle, eccentricity ratio, eccentricity throw and proportional coefficient of center distance.
集成型的差速室、准双曲面齿轮的设计中，小齿轮组中心线在环形齿轮的中心线之上。
The integral type housing, hypoid gear design has the centerline of the pinion set above the centerline of the ring gear.
研究了基于齿轮测量中心检测凸轮的基本原理，并解决了测量过程中凸轮轮廓线拟合、测头控制策略和补偿等问题。
This paper studies the basic principle of detecting cam based on the Gear Measuring Center, and solves such key problems as cam contour matching, compensation and controlling strategy for the probe.
弯曲补偿，这为广泛齿轮盒的补偿车轮中心的地位。
This bend compensates for the wide gear cassette that offsets the center of the wheel.
本文是以如何提高大型数控齿轮测量中心测量精度为目的而展开研究的。
The focus of this paper is how to enhance the measuring accuracy of CNC gear measuring machine.
给出了非圆齿轮的节曲线极坐标方程，两齿轮中心距的计算方法，节曲线长度、基础圆半径和压力角的计算公式。
The polar equation of non-circular gear pitch curve, calculation method of center distance, formula of pitch curve length, primary circle radius and pressure Angle is given.
通过几何分析的方法，导出了内啮合渐开线齿轮传动中心距略变小时，法向齿侧间隙的计算公式，供齿轮传动设计计算之用。
By using geometry analysis method, this paper educed calculation formula of normal direction gear side clearance when internal gearing involute gear transmission center distance waned slightly.
利用随机模拟方法给出了可调中心距齿轮链空程在各种情况下的模拟曲线及计算结果。
In this paper, the simulate curve and result for the backlash Center Adjustable Gear train in various cases are given by the random simulate method.
螺旋锥齿轮副的成形法大轮，利用合适的成形铣刀，在通用的立式加工中心上，可以实现热处理后硬齿面的高速铣削。
For spiral bevel gears' formate gear, using proper figurate cutting tool and generic CNC machining center, the gear's hard tooth-surface can be milled with high speed.
其次，对多齿轮泵的静力学特性作了分析，证明了中心轮径向液压力、啮合力及总作用力平衡。
Secondly, analyzing statics characteristic of the multi-gear pump demonstrates that radial hydraulic pressure, meshing force and resultant force are balanced on the center wheel.
由于设计参数的不同，当样板用于齿轮测量中心等齿轮仪器的校准时，常需要进行参数换算。
When the master is used to calibrate gear measurement equipments, such as the gear measurement center, parameters need to be converted frequently because of the different designed parameters.
双圆弧齿轮减速器中心距和传动比分配的确定，直接影响减速器承载能力、重量和体积。
The selection of center distance and gear ratio distribution for a reducer with double-circular-arc gear will have a direct effect on its size, weight and loading capacity.
双圆弧齿轮减速器中心距和传动比分配的确定，直接影响减速器承载能力、重量和体积。
The selection of center distance and gear ratio distribution for a reducer with double-circular-arc gear will have a direct effect on its size, weight and loading capacity.
应用推荐