中心电极组件及其生产方法，不可逆电路装置，通信装置。
Central electrode subassembly and its production method, nonreciprocal circuit device, communication device.
因此，导电液水准仪在电性能上相当于一电位计，中心电极相当于转臂。
The electrolytic level is therefore electrically equivalent to a potentiometer, the center electrode corresponding to the rotor arm.
火花由在中心电极和旁电极之间的高电压(大约6千伏到40千伏)产生。
A spark is produced by applying a high voltage (from approximately 6 KV to 40 KV) between the center electrode and ground.
该中心电极1.0的世界粮食理事会已与薄胶塑料布覆盖，因此要得到完全绝缘阴极。
The center electrode of the WFC v1.0 has been covered with a thin adhesive plastic sheet so has to get a fully insulated cathod.
中心电极越细所产生的火花越强、当电量集中与一点时，即使在相对较低的电压下也会发生点火现象。
The spark is more stronger when the central electrode is thiner. even at a relatively low voltage ignition phenomena also occur when the power concentrate at a plot.
当电极厚度增加时，通带的涟波会变小，中心频率会降低。
With electrode thickness increases, passband ripple becomes smaller, center frequency moves toward lower frequency.
离散相介质的存在对激励电极和测量电极附近区域灵敏场的影响比较大，对管道中心区域的影响则比较小。
The effect in the vicinity of the exciting electrode and detecting electrode is greater than that of the center of the pipe.
在离开放电单元的中心部分的方向上凸出的第二凸出电极可有利于增加放电单元内的放电扩散效率。
A second projection electrode projecting in a direction away from the central portion of the discharge cell can be advantageous of increasing discharge diffusion efficiency within the discharge cell.
基于已有模型的结构特点设计了电磁系统的改进方案，通过分析比较活动电极电磁吸力的分布规律，确定了中心平面线圈结构设计方案将更加合理。
The revised schemes were designed basing on the original model features, and central planer coil structure was preferable by analyzing electromagnetic attraction force of movable contact.
第一电极区分布在第一接触电极绕旋转件的旋转中心在固定件上旋转所覆盖的区域。
The first electrode area is distributed in the area covered by the first contact electrode which rotates on the fixed part around the rotating center of the rotating part.
第二电极区分布在第二接触电极绕旋转件的旋转中心在固定件上旋转所覆盖的区域。
The second electrode areas are distributed in the area covered by the second contact electrode which rotates on the fixed part around the rotating center of the rotating part.
试验换热管为垂直套管式，外层为加热水路，内层为工质回路，中心布置着电极。
The test section was a vertical tube-in-tube heat exchanger with hot water in the annulus and the test refrigerant in the inner tube.
该中心导线组件包括点火电极、导电玻璃密封、一个中间电极、噪音抑制玻璃密封和一个端电极。
The center wire assembly includes a firing electrode, a conductive glass seal, an intermediate electrode, the noise suppressing glass seal, and a terminal electrode.
主要研究内容如下：1、针对零件的不同结构和加工要求，研究并实现了两轴电火花线切割多次切割电极丝中心轨迹的生成算法。
The wire path generation of multiple-cut in 2-axis WEDM is researched. Then an algorithm named Virtual Wire Model is presented.
主要研究内容如下：1、针对零件的不同结构和加工要求，研究并实现了两轴电火花线切割多次切割电极丝中心轨迹的生成算法。
The wire path generation of multiple-cut in 2-axis WEDM is researched. Then an algorithm named Virtual Wire Model is presented.
应用推荐