断掉一切后路，离开那个不锈钢接头错误的开始。
黑铁壳，黑铁圈，玻璃面，铜机芯，铜管子，不锈钢接头。
Black steel case, black stack steel ring, glass lens, brass internal and connection, stainless steel joint.
本文研究了影响镍基钎料钎焊不锈钢接头性能的主要工艺参数。
Main technology parameters of effects on brazing stainless steel joints using nickel base filler metal have been studied.
不锈钢壳，不锈钢压圈，玻璃面，不锈钢机芯，不锈钢管子，不锈钢接头。
Stainless steel case and ring, glass lens, stainless steel internal, connection and joint, ammonia pressure gauge.
本文讨论和分析了18 - 8奥氏体不锈钢接头晶间腐蚀问题，提出了相应的控制措施。
The article discussed and analysed 18-8 Austenite stainless steel joint question about Intercrystalline Corrosion, then it put forward appropriate measurements.
采用先在钎缝间隙中预填合金粉，然后在钎缝外置放钎料进行钎焊的方法，解决不锈钢接头宽间隙的钎焊问题。
The braze of stainless steel joints with wide clearance is made by pre filling alloy powder into the gap.
研究了奥氏体不锈钢焊接接头在不同酸性介质中的腐蚀行为。
The corrosion behavior of austenite stainless steel weld joint in the different acidic medium was studied.
此外，我公司还承接各种特殊连接形式，非标准旋转接头和金属软管及不锈钢法兰的设计、制造。
In addition, I also take the form of a variety of special connections, non-standard rotary joints and metal hoses and stainless steel flange design, manufacture.
通过对13 -5型马氏体不锈钢焊接接头进行等离子弧清根及碳弧气刨清根的比较，证明等离子弧清根对全焊透焊缝实施背面清根是可行的。
By comparing backgouging of plasma arc with carbon arc to the welded joint of 13-5 martensitic stainless steel, the backgouging of plasma arc is proved feasible for the full penetration weld.
分析了不锈钢压力表管接头焊缝开裂的原因，认为此种开裂具有应力腐蚀开裂、沿晶断裂特征。
The rupture reasons of tube joint weld of the stainless steel pressure meter are analyzed. It is characteristic of stress corrosion cracking and inter granular fracture.
T CS铁素体不锈钢采用奥氏体型焊材，实芯焊丝、药芯焊丝和电焊条方法，焊接接头力学性能可以满足使用要求。
With austenitic welding material, solid wire, flux-cored wire and electrode, welded joint mechanical property of TCS ferritic stainless steel all can meet usability.
不锈钢外壳，美观大方。配快速接头，使用方便灵活。
Good-looking with stainless steel casing. Convenient to use with quick connectors.
在TCS不锈钢前期焊接试验中发现其焊接接头热影响区的冲击吸收功值在熔合线附近较低，原因是接头热影响区晶粒粗大所致。
In welding test of TCS stainless steel, it was found that impact absorbing energy of heat-affected zone (HAZ) near bond line in welded joint was low.
采用过渡层法进行钛合金与不锈钢的焊接时，基本能够避免焊接材料之间脆性金属间化合物的大量生成，从而有效提高焊接接头的连接强度。
The intermetallics could be avoided effectively by using the method of transition layers between titanium alloy and stainless steel, and the tensile strength of welded joints is enhanced.
不锈钢快速接头系列；
本产品由内外不锈钢螺纹接头、不锈钢波纹管外包不锈钢网管等组成。
Inlet and outlet stainless steel connector stainless steel bellow is wrapped with stainless steel net pipe.
在TCS不锈钢前期焊接试验中发现其焊接接头热影响区的冲击吸收功值在熔合线附近较低，原因是接头热影响区晶粒粗大所致。
In welding test of TCS stainless steel, it was found that impact absorbing energy of heat-affected zone (HAZ) near bond line in welded joint was low. The reason is coarse grain in HAZ.
从钎缝断口分析也证明钎缝中靠近不锈钢一侧是接头最薄弱的位置。
Joint failure analysis showed that the weakest occurred at the place near the stainless steel.
通过金相观察、力学性能和耐晶间腐蚀性能试验，研究了SUS 304不锈钢M AG焊接头组织与性能。
The microstructure and properties of steel SUS304 MAG welded joint was studied through metallograph observation and property tests.
平衡铁素体和奥氏体两相组织在焊缝金属和热影响区中的比例，保证焊接接头的性能，是双相不锈钢焊接的基本要求。
The basic requirement of welding the steel 2205 is that the weld metal and heat-affected zone obtain a favorable phase balance and retain the performance as the base metal after welding.
平衡铁素体和奥氏体两相组织在焊缝金属和热影响区中的比例，保证焊接接头的性能，是双相不锈钢焊接的基本要求。
The basic requirement of welding the steel 2205 is that the weld metal and heat-affected zone obtain a favorable phase balance and retain the performance as the base metal after welding.
应用推荐